Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM38G0E _59 Vehicle Exterior _100826 SLIDING ROOF / CONVERTIBLE _0469275 SLIDING ROOF SYSTEM J

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  Sliding Roof does not Move by Operating Sliding Roof Control Switch  


DESCRIPTION

The sliding roof ECU (sliding roof drive gear assembly) receives slide and tilt signals and operates its built-in motor when the sliding roof switch (map light assembly) is operated.

WIRING DIAGRAM

E468264E01
0.5,4.729 2.396,5.25 1.896,0.521 10 false Sliding Roof Switch (Map Light Assembly) 4.635,4.875 6.573,5.333 1.938,0.458 10 true Sliding Roof ECU (Sliding Roof Drive Gear Assembly) 1.833,1.094 3.344,1.344 1.51,0.25 10 false from Battery 2.115,2.76 3.625,3.01 1.51,0.25 10 false UP 1.885,3.146 3.396,3.396 1.51,0.25 10 false DOWN 3.396,1.292 4.906,1.542 1.51,0.25 10 false S/ROOF 4.438,1.021 4.698,1.292 0.26,0.271 10 false B 4.427,2.01 5.938,2.26 1.51,0.25 10 false OPN 4.458,2.396 5.969,2.646 1.51,0.25 10 false CLS 4.438,2.781 5.948,3.031 1.51,0.25 10 false UP 4.438,3.156 5.948,3.406 1.51,0.25 10 false DWN 4.438,3.521 4.958,3.896 0.521,0.375 10 false E 2.021,2.01 3.531,2.26 1.51,0.25 10 false OPN 2.031,2.396 3.542,2.646 1.51,0.25 10 false CLS 1.948,3.531 3.458,3.781 1.51,0.25 10 false GND5 4.646,4.708 6.156,4.958 1.51,0.25 10 false d19 4.24,1.01 4.5,1.281 0.26,0.271 10 false 1 4.188,2.01 4.448,2.281 0.26,0.271 10 false 10 4.26,2.375 4.521,2.646 0.26,0.271 10 false 8 4.26,2.74 4.521,3.01 0.26,0.271 10 false 5 4.26,3.125 4.521,3.396 0.26,0.271 10 false 9 4.271,3.521 4.531,3.792 0.26,0.271 10 false 2 2.5,1.906 2.76,2.177 0.26,0.271 10 false 1 2.5,2.313 2.76,2.583 0.26,0.271 10 false 6 2.49,2.698 2.75,2.969 0.26,0.271 10 false 2 2.49,3.063 2.75,3.333 0.26,0.271 10 false 7 2.479,3.438 2.74,3.708 0.26,0.271 10 false 24 2.479,2.104 2.667,2.292 0.188,0.188 10 false d2 2.49,2.479 2.677,2.667 0.188,0.188 10 false d2 2.49,2.865 2.677,3.052 0.188,0.188 10 false d2 2.49,3.25 2.677,3.438 0.188,0.188 10 false d2 2.479,3.625 2.667,3.813 0.188,0.188 10 false d1 1.948,3.938 3.458,4.188 1.51,0.25 10 false GND9 2.49,4.031 2.677,4.219 0.188,0.188 10 false d1 2.479,3.854 2.74,4.125 0.26,0.271 10 false 10

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the sliding roof ECU (sliding roof drive gear assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear assembly) must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

If a sliding roof ECU (sliding roof drive gear assembly) DTC is output, first perform troubleshooting for the sliding roof ECU (sliding roof drive gear assembly) DTC.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SLIDING ROOF)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Sliding Roof > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Slide Roof Operate sliding roof motor OFF / Opn/Dwn / Clos/Up -
Body Electrical > Sliding Roof > Active Test
Tester Display
Slide Roof
50004 147 1
OK:

Slide roof is operated using GTS.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - BATTERY AND BODY GROUND)
2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch OPEN switch signal OFF or ON OFF: OPEN switch not pressed
ON: OPEN switch pressed
-
Close Switch CLOSE switch signal OFF or ON OFF: CLOSE switch not pressed
ON: CLOSE switch pressed
-
Up Switch UP switch signal OFF or ON OFF: UP switch not pressed
ON: UP switch pressed
-
Down Switch DOWN switch signal OFF or ON OFF: DOWN switch not pressed
ON: DOWN switch pressed
-
Body Electrical > Sliding Roof > Data List
Tester Display
Open Switch
Close Switch
Up Switch
Down Switch
50003 147 1,4,7,10
OK:

The GTS display changes according to the operation of each switch as shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

3.INSPECT SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)
3.INSPECT SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)

OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)

NG

REPLACE SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)
a.

Disconnect the d1 and d2 sliding roof switch (map light assembly) connector.


b.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d19,d2,d1)Location & Routing

Click Connector(d19)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Assembly)

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

Click Connector(d1)Body>No. 1 Roof Wire>Map Light Assembly (Front)

d19-8 (CLS) - d2-6 (CLS) Always Below 1 Ω
d19-8 (CLS) or d2-6 (CLS) - Body ground Always 10 kΩ or higher
d19-10 (OPN) - d2-1 (OPN) Always Below 1 Ω
d19-10 (OPN) or d2-1 (OPN) - Body ground Always 10 kΩ or higher
d19-9 (DWN) - d2-7 (DOWN) Always Below 1 Ω
d19-9 (DWN) or d2-7 (DOWN) - Body ground Always 10 kΩ or higher
d19-5 (UP) - d2-2 (UP) Always Below 1 Ω
d19-5 (UP) or d2-2 (UP) - Body ground Always 10 kΩ or higher
d1-24 (GND5) - Body ground Always Below 1 Ω
d1-10 (GND9) - Body ground Always Below 1 Ω
d19-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - BATTERY AND BODY GROUND)
a.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(d19)Location & Routing

Click Connector(d19)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Assembly)

d19-1 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d19)Location & Routing

Click Connector(d19)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Assembly)

d19-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR