| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C061012 | Right Electric Parking Brake Actuator Control Circuit Short to Battery |
·
Diagnosis Condition: Electric parking brake not operating
·
Malfunction Status: The ECU power supply is normal but there is a malfunction in the electric parking brake actuator RH internal circuit (short to +B).
·
Detection Time: Approximately 1 second |
·
Parking brake actuator assembly RH
·
No. 1 parking brake wire assembly
·
Wire harness or connector
·
No. 2 skid control ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
To ensure that the electric parking brake does not operate, wait for 4 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.
After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned ON.
Turn the ignition switch off.
Make sure the No. 1 parking brake wire assembly is securely installed.
Disconnect the s2 parking brake actuator assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(s2)Location & Routingewd_type=routing;type=c;code=s2 Click Connector(s2)Body>No. 1 Parking Brake Wire Assembly>Parking Brake Actuator Assembly RHewd_type=component;type=c;code=s2;pinno=2,1 |
||
| s2-2 - s2-1 | Electric parking brake not operating | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Vs1 No. 1 parking brake wire assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Vs1)Location & Routingewd_type=routing;type=w;code=Vs1 Click Connector(Vs1)Body>Differential Wire / Frame Wire>Frame Wire and No. 1 Parking Brake Wire Assemblyewd_type=component;type=w;code=Vs1;pinno=2,5 |
||
| Vs1-2 - Vs1-5 | Electric parking brake not operating | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Vs1 No. 1 parking brake wire assembly connector.
Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Vs1,B20)Location & Routingewd_type=routing;type=w,c;code=Vs1,B20 Click Connector(Vs1)Body>Differential Wire / Frame Wire>Frame Wire and No. 1 Parking Brake Wire Assemblyewd_type=component;type=w;code=Vs1;pinno=2,5 |
||
| Vs1-2 or B20-13 (MRR+) - Body ground | Always | Below 1 V |
| Vs1-5 or B20-12 (MRR-) - Body ground | Always | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
NG