Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM
RM38G0E _54 Brake _100998 PARKING BRAKE _0469398 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C102016  Ignition Switch On/Start Position Circuit Voltage Below Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C102016 Ignition Switch On/Start Position Circuit Voltage Below Threshold
·

Diagnosis Condition:

Ignition switch ON

·

Malfunction Status:

When the ECM is communicating via CAN communication, IG power is not input to the No. 2 skid control ECM (brake actuator assembly).

·

Detection Time:

Approximately 15 seconds


·

Wire harness and connector

·

Backup boost converter circuit*

·

No. 2 skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

*: w/ Stop and Start System


WIRING DIAGRAM

C460131E01
1.688,1.583 2.917,1.781 1.229,0.198 10 false ECU-IGR NO. 3 4.188,1.427 4.625,1.667 0.438,0.24 10 false IG1 3.885,1.313 4.323,1.552 0.438,0.24 10 false 45 4.167,2.156 4.667,2.406 0.5,0.25 10 false B20 4.167,2.333 5.906,2.958 1.74,0.625 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 3.052,1.292 3.49,1.531 0.438,0.24 10 false *1 3.052,2.177 3.49,2.417 0.438,0.24 10 false *2 0.125,3.302 3.333,3.5 3.208,0.198 10 false *2: w/ Stop and Start System 0.125,2.885 3.333,3.083 3.208,0.198 10 false *1: w/o Stop and Start System 1.51,2.208 2.5,2.563 0.99,0.354 10 false Engin Stop and Start ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

To ensure that the electric parking brake does not operate, wait for 4 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned ON.



PROCEDURE

1.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL VOLTAGE)

B

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL VOLTAGE)
a.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-45 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-45 (IG1) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

NG

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)