Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)
RM38G0E _55 Steering _100915 POWER ASSIST SYSTEMS _0469466 POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve)  C18BA16  Power Steering "B" Motor "A" Supply Voltage Circuit Voltage Below Threshold  C18BA17  Power Steering "B" Motor "A" Supply Voltage Circuit Voltage Above Threshold  C18BD16  Power Steering "B" Motor "B" Supply Voltage Circuit Voltage Below Threshold  C18BD17  Power Steering "B" Motor "B" Supply Voltage Circuit Voltage Above Threshold  


DESCRIPTION

If a problem occurs in the system, the power source relay circuit and the motor relay circuit are shut off to stop power assist. The ECU must be replaced when there is a problem with the relays because the relays are built into the ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C18BA16 Power Steering "B" Motor "A" Supply Voltage Circuit Voltage Below Threshold Motor "1" PIG voltage is less than 3.6 V
·

EPS NO. 1 fuse

·

PIG power source circuit

·

Power steering ECU with motor assembly


Output ECU: Power steering ECU with motor assembly
C18BA17 Power Steering "B" Motor "A" Supply Voltage Circuit Voltage Above Threshold Diagnosis Condition: Ignition switch ON
Malfunction Status: Motor "1" PIG voltage is more than 19.6 V
·

EPS NO. 1 fuse

·

PIG power source circuit

·

Power steering ECU with motor assembly


Output ECU: Power steering ECU with motor assembly
C18BD16 Power Steering "B" Motor "B" Supply Voltage Circuit Voltage Below Threshold Motor "2" PIG voltage is less than 3.6 V
·

EPS NO. 1 fuse

·

PIG power source circuit

·

Power steering ECU with motor assembly


Output ECU: Power steering ECU with motor assembly
C18BD17 Power Steering "B" Motor "B" Supply Voltage Circuit Voltage Above Threshold Diagnosis Condition: Ignition switch ON
Malfunction Status: Motor "2" PIG voltage is more than 19.6 V
·

EPS NO. 1 fuse

·

PIG power source circuit

·

Power steering ECU with motor assembly


Output ECU: Power steering ECU with motor assembly

WIRING DIAGRAM

C322363E75
5.479,2.958 7.042,3.313 1.563,0.354 10 false Power Steering ECU with Motor Assembly 1.958,0.688 2.865,0.906 0.906,0.219 10 false from Battery 3.625,0.896 4.573,1.167 0.948,0.271 10 false EPS NO. 1 5.677,0.74 6.219,1 0.542,0.26 10 false PIG 5.677,1.906 6.219,2.167 0.542,0.26 10 false PGND 5.51,0.625 6.052,0.885 0.542,0.26 10 false 1 5.5,1.792 6.042,2.052 0.542,0.26 10 false 2 5.479,2.792 6.021,3.052 0.542,0.26 10 false I70

CAUTION / NOTICE / HINT

NOTICE:
·

When the power steering ECU with motor assembly has been replaced, perform Steering Actuator ECU Initial Setting (assist map writing).

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU WITH MOTOR ASSEMBLY - BODY GROUND)
a.

Disconnect the I70 power steering ECU with motor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I70)Location & Routing

Click Connector(I70)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Power Steering ECU Assembly

I70-1 (PIG) - Body ground Engine running 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I70)Location & Routing

Click Connector(I70)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Power Steering ECU Assembly

I70-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR