Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  VSC OFF Switch Circuit  


DESCRIPTION

The No. 2 skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the "Traction Control Turned Off" will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C427345E19
0.917,0.896 1.375,1.104 0.458,0.208 10 false CANL 0.906,1.729 1.344,1.927 0.438,0.198 10 false CANH 1.396,0.74 1.708,0.938 0.313,0.198 10 false 29 1.406,1.552 1.719,1.75 0.313,0.198 10 false 13 5.073,0.74 5.385,0.938 0.313,0.198 10 false 43 5.073,1.552 5.385,1.75 0.313,0.198 10 false 27 5.354,0.896 5.792,1.104 0.438,0.208 10 false CANL 5.354,1.719 5.833,1.906 0.479,0.188 10 false CANH 3.469,2.75 3.625,2.948 0.156,0.198 10 false 2 4.542,2.75 4.698,2.948 0.156,0.198 10 false 5 0.146,3.823 0.479,4.01 0.333,0.188 10 false I5 3.521,3.24 3.844,3.438 0.323,0.198 10 false I77 3.542,3.427 5.188,3.781 1.646,0.354 10 false VSC OFF Switch 3.688,2.99 3.844,3.188 0.156,0.198 10 false E 4.344,2.979 4.5,3.177 0.156,0.198 10 false + 5.156,2.74 5.469,2.938 0.313,0.198 10 false 9 5.365,2.99 5.823,3.188 0.458,0.198 10 false CSW 5.104,3.906 5.563,4.104 0.458,0.198 10 false B20 5.094,4.083 6.99,4.49 1.896,0.406 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 2.896,4.323 4.615,4.531 1.719,0.208 10 false : CAN Communication Line 0.135,3.979 2,4.188 1.865,0.208 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Check that the indicator light and mode condition on the GTS change according to VSC OFF switch operation.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC(TRAC)/VSC OFF Mode TRC/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode
VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode
-
Chassis > Brake/EPB > Data List
Tester Display
TRC(TRAC)/VSC OFF Mode
50003 435 45
Standard:
Switch Operation Mode Condition Display Multi-information Display (Traction Control Turned Off) VSC OFF Indicator Light
Not pressed Normal mode (TRC(TRAC) ON/VSC ON) Not displayed Does not come on
Pressing the VSC OFF switch TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) Displayed Does not come on
Pressing and holding the VSC OFF switch VSC OFF mode (TRC(TRAC) OFF/VSC OFF) Displayed Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

2.INSPECT VSC OFF SWITCH

B

C

2.INSPECT VSC OFF SWITCH

OK

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)

NG

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B20,I77)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

Click Connector(I77)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>VSC OFF Switch

B20-9 (CSW) - I77-5 (+) Always Below 1 Ω
B20-9 (CSW) or I77-5 (+) - Body ground Always 10 kΩ or higher
I77-2 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR