Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2021.04–2022.11
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Brake Hold Standby Indicator Light Circuit  


DESCRIPTION

The brake hold standby indicator light turns on if brake hold control is possible when the following conditions required for operation standby are met and the brake hold switch (electric parking brake switch assembly) is pressed while the ignition switch is turned to ON.

Conditions required for operation standby:

(a)

The driver door is closed.

(b)

The driver seat belt is fastened.

(c)

The system is normal.



WIRING DIAGRAM

C427349E16
0.906,0.906 1.521,1.104 0.615,0.198 10 false CANL 0.885,1.74 1.5,1.938 0.615,0.198 10 false CANH 1.406,0.74 1.719,0.938 0.313,0.198 10 false 29 1.406,1.552 1.719,1.75 0.313,0.198 10 false 13 5.073,0.74 5.385,0.938 0.313,0.198 10 false 43 5.073,1.552 5.385,1.75 0.313,0.198 10 false 27 5.365,0.906 5.823,1.104 0.458,0.198 10 false CANL 5.365,1.719 5.844,1.917 0.479,0.198 10 false CANH 3.396,2.75 3.667,3.01 0.271,0.26 10 false 12 4.542,2.75 4.813,3 0.271,0.25 10 false 10 0.115,3.906 0.573,4.104 0.458,0.198 10 false I5 3.052,3.177 3.51,3.375 0.458,0.198 10 false I89 3.042,3.354 5.229,3.896 2.188,0.542 10 false Brake Hold Switch (Electric Parking Brake Switch Assembly) 3.677,2.99 3.833,3.188 0.156,0.198 10 false E 4.125,2.99 4.563,3.219 0.438,0.229 10 false SLT1 5.073,2.76 5.385,2.958 0.313,0.198 10 false 35 5.375,3.052 5.833,3.25 0.458,0.198 10 false BH 5.135,3.938 5.594,4.135 0.458,0.198 10 false B20 5.125,4.104 7.052,4.51 1.927,0.406 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 2.906,4.323 4.635,4.542 1.729,0.219 10 false : CAN Communication Line 0.115,4.073 4.094,4.271 3.979,0.198 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.PRE-CHECK
a.

If the brake hold standby indicator light does not illuminate even though the brake hold switch (electric parking brake switch assembly) is pushed, check that the brake hold function operation conditions are met.

1.

The driver door is closed.

2.

The driver seat belt is fastened.

3.

The system is normal.


HINT:

If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.

·

Brake system

·

Electric parking brake system

·

Engine control system




Result:
Proceed to
NEXT



NEXT

2.READ VALUE USING GTS (BRAKE HOLD READY)
2.READ VALUE USING GTS (BRAKE HOLD READY)
a.

Check the brake hold standby indicator light and mode condition on the GTS changes according to brake hold switch (electric parking brake switch assembly) operation.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Hold Ready Brake hold control permission status Not in stand-by mode / Stand-by mode Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated)
Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated)
-
Chassis > Brake/EPB > Data List
Tester Display
Brake Hold Ready
50003 435 164
Standard:
Brake Hold Switch Operation Mode Condition Display Brake Hold Standby Indicator Light
Not pressed Not in stand-by mode Does not come on
Pressing the brake hold switch Stand-by mode Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

3.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

B

C

3.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B20,I89)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

Click Connector(I89)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Electric Parking Brake Switch Assembly

B20-35 (BH) - I89-10 (SLT1) Always Below 1 Ω
B20-35 (BH) or I89-10 (SLT1) - Body ground Always 10 kΩ or higher
I89-12 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR