Refer to DTC C050C12.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C050C12
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Note |
|---|---|---|---|---|---|
| C050C23 | Left Rear Wheel Speed Sensor Signal Stuck Low | Any of the following is detected:
·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more.
·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.
·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both speed sensors are 0 km/h (0 mph) for 30 seconds or more. |
·
Rear speed sensor LH
·
Rear speed sensor installation
·
Skid control sensor wire LH (No. 2 parking brake wire assembly)
·
Wire harness and connector
·
Rear speed sensor rotor LH (rear axle hub and bearing assembly LH) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | When the +BS terminal voltage is 17.4 V or less | ○ | ○ | ○ |
| Malfunction Status | At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors | ○ | - | - |
| At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) | - | ○ | - | |
| At a vehicle speed of 10 km/h (6 mph) or more, outputs from both speed sensors are 0 km/h (0 mph) | - | - | ○ | |
| Detection Time | 30 seconds or more. | 1 second or more. | 30 seconds or more. | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
Refer to DTC C050C12.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C050C12
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
| *a | Correct |
| *b | Incorrect |
Check the rear speed sensor LH installation.
There is no clearance between the rear speed sensor LH and the rear axle housing assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speed sensor LH.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL
Check the rear speed sensor tip LH.
The rear speed sensor tip LH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the rear speed sensor LH, clean the rear speed sensor LH.
If the rear speed sensor LH is damaged, replace the rear speed sensor LH with a new one.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a road test.
Check the rear speed sensor LH output value.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph) Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| RL Wheel Speed |
The output value changes in accordance with the vehicle speed.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the t1 and Vt1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(t1,Vt1)Location & Routingewd_type=routing;type=c,w;code=t1,Vt1 Click Connector(t1)Body>No. 2 Parking Brake Wire Assembly>Rear Speed Sensor LHewd_type=component;type=c;code=t1;pinno=2,1 Click Connector(Vt1)Body>Differential Wire / Frame Wire>Frame Wire and No. 2 Parking Brake Wire Assemblyewd_type=component;type=w;code=Vt1;pinno=1,4 |
||
| t1-2 - Vt1-1 | Always | Below 1 Ω |
| t1-2 or Vt1-1 - Body ground and other terminals | Always | 10 kΩ or higher |
| t1-1 - Vt1-4 | Always | Below 1 Ω |
| t1-1 or Vt1-4 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Vt1,B20)Location & Routingewd_type=routing;type=w,c;code=Vt1,B20 Click Connector(Vt1)Body>Differential Wire / Frame Wire>Frame Wire and No. 2 Parking Brake Wire Assemblyewd_type=component;type=w;code=Vt1;pinno=1,4 |
||
| Vt1-1 - B20-5 (RL+) | Always | Below 1 Ω |
| Vt1-1 or B20-5 (RL+) - Body ground | Always | 10 kΩ or higher |
| Vt1-4 - B20-4 (RL-) | Always | Below 1 Ω |
| Vt1-4 or B20-4 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the component with the rear speed sensor rotor LH.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>DISASSEMBLY
Check the rear speed sensor rotor LH.
The rear speed sensor rotor LH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the rear speed sensor rotor LH, clean the rear speed sensor rotor LH.
Do not use parts cleaner when cleaning the rear speed sensor rotor LH.
If the rear speed sensor rotor LH is damaged, replace the rear speed sensor rotor LH with a new one.
The rear speed sensor rotor LH is incorporated into the rear axle hub and bearing assembly LH.
If the rear speed sensor rotor LH needs to be replaced, replace it together with the rear axle hub and bearing assembly LH.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The rear speed sensor rotor LH is damaged.) | B |
| NG (There is foreign matter on the rear speed sensor rotor LH.) | C |
A
B
C