Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C051212  Right Rear Wheel Speed Sensor Circuit Short to Battery  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the No. 2 skid control ECU (brake actuator assembly). These signals are used for brake control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the No. 2 skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and No. 2 skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C457031E01
3.677,0.594 4.073,0.219 4.073,0.219 4.26,0.219 true 4.74,0.99 6.573,1.188 1.833,0.198 10 false Forward 4.344,0.135 6.177,0.333 1.833,0.198 10 false Speed Sensor 1.875,1.052 3.708,1.25 1.833,0.198 10 false Backward 3.021,2 4.854,2.198 1.833,0.198 10 false Speed Sensor Rotor 1.875,4.479 3.708,4.677 1.833,0.198 10 false Backward 2.906,4.479 4.74,4.677 1.833,0.198 10 false Forward 6.521,3.042 7.021,3.24 0.5,0.198 10 false 14 mA 5.104,3.979 6.26,4.24 1.156,0.26 10 false High speed 6.521,2.552 7.021,2.75 0.5,0.198 10 false 26 mA 6.542,3.5 7.042,3.698 0.5,0.198 10 false 7 mA 3.708,3.979 4.865,4.24 1.156,0.26 10 false Low speed

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C051212 Right Rear Wheel Speed Sensor Circuit Short to Battery The speed sensor short signal is ON continuously for 0.5 seconds or more.
·

Rear speed sensor RH

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)

·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

WIRING DIAGRAM

C460011E02
0.073,2.292 1.542,2.615 1.469,0.323 10 false Rear Speed Sensor RH 1.854,2.292 3.969,2.677 2.115,0.385 10 false Skid control sensor wire RH (No. 1 Parking Brake Wire Assembly) 5.188,3.094 7.104,3.729 1.917,0.635 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 5.792,1.031 6.292,1.271 0.5,0.24 10 false RR+ 5.792,1.719 6.292,1.927 0.5,0.208 10 false RR- 1.667,1.104 2.219,1.344 0.552,0.24 10 false s1 1.656,1.802 1.99,2.052 0.333,0.25 10 false s1 3.198,1.125 3.688,1.344 0.49,0.219 10 false Vs1 3.208,1.813 3.625,2.115 0.417,0.302 10 false Vs1 1.698,0.906 2,1.135 0.302,0.229 10 false 2 5.188,2.906 5.688,3.104 0.5,0.198 10 false B20 1.688,1.594 1.99,1.823 0.302,0.229 10 false 1 3.292,0.906 3.594,1.135 0.302,0.229 10 false 1 3.302,1.594 3.604,1.823 0.302,0.229 10 false 4 5.521,1.021 5.813,1.26 0.292,0.24 10 false 20 5.51,1.698 5.865,1.948 0.354,0.25 10 false 19

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the s1 rear speed sensor RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(s1)Location & Routing

Click Connector(s1)Body>No. 1 Parking Brake Wire Assembly>Rear Speed Sensor RH

s1-2 - s1-1 Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the Vs1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(Vs1)Location & Routing

Click Connector(Vs1)Body>Differential Wire / Frame Wire>Frame Wire and No. 1 Parking Brake Wire Assembly

Vs1-1 - Vs1-4 Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(Vs1)Location & Routing

Click Connector(Vs1)Body>Differential Wire / Frame Wire>Frame Wire and No. 1 Parking Brake Wire Assembly

Vs1-4 - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR