Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C134551  Linear Solenoid Valve Offset Learning Not Programmed  C134554  Linear Solenoid Valve Offset Learning Missing Calibration  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C134551 Linear Solenoid Valve Offset Learning Not Programmed The linear solenoid valve offset learning value is not stored.
·

Perform linear solenoid valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal.

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
HINT:

During Dealer Mode, related DTCs are cleared.


C134554 Linear Solenoid Valve Offset Learning Missing Calibration The linear solenoid valve offset learning value cannot be obtained.
·

Perform linear solenoid valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal.

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK DTC
a.

Check that no DTCs other than those related to incomplete learning are output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435
OK:

DTCs other than those related to incomplete learning are not output.



Result:
Proceed to
OK
NG



OK

2.PERFORM AIR BLEEDING

NG

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.PERFORM AIR BLEEDING

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING

Result:
Proceed to
NEXT



NEXT

3.PERFORM LINEAR SOLENOID VALVE OFFSET LEARNING
3.PERFORM LINEAR SOLENOID VALVE OFFSET LEARNING
a.

Check and ensure the following conditions required for performing linear solenoid valve offset learning and then perform linear solenoid valve offset learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

NOTICE:

If DTC C134554 is output, turn the ignition switch off for 3 minutes or more, turn the ignition switch to ON again, and then clear the DTC before performing learning.


Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 5554
1.

The battery voltage is 11 to 14 V when the ignition switch is ON.

2.

The brake booster with master cylinder assembly is not hot.

3.

The engine control system is not malfunctioning.

4.

The shift state indicator shows that the shift lever is in P.

5.

The brake pedal is not depressed.

6.

The parking brake is released.

7.

DTCs C145151 is not output. (If it is output, bleed the air from the high-pressure tube.)



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
C134551 and C134554 are not output A
C134551 or C134554 is output B



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY