The airbag sensor with ECU assembly has a built-in yaw rate and acceleration sensor.
The No. 2 skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor with ECU assembly) via CAN communication.
If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag sensor with ECU assembly) and the CAN communication system, DTC U012587 is output. When DTC U012587 is output together with C051D54 and/or C121054, inspect and repair the trouble areas indicated by U012587 first.
These DTCs are also output when the calibration has not been completed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Note |
|---|---|---|---|---|---|
| C051D54 | Multi-axis Acceleration Sensor Module "A" Missing Calibration | Zero point calibration of acceleration sensor undone. |
·
Acceleration sensor zero point not calibrated
·
Acceleration sensor (airbag sensor with ECU assembly) installation
·
Acceleration sensor (airbag sensor with ECU assembly)
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C121054 | Yaw Rate Sensor Missing Calibration | Zero point calibration of yaw rate sensor undone. |
·
Yaw rate sensor zero point not calibrated
·
Yaw rate sensor (airbag sensor with ECU assembly) installation
·
Yaw rate sensor (airbag sensor with ECU assembly)
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor with ECU assembly), perform "Calibration".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
Perform zero point calibration of the yaw rate and acceleration sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
| Tester Display |
|---|
| Calibration |
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C051D54 and C121054 are not output | A |
| C051D54 or C121054 is output | B |
A
B
Turn the ignition switch off.
Check that the yaw rate and acceleration sensor (airbag sensor with ECU assembly) has been installed properly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
The yaw rate and acceleration sensor (airbag sensor with ECU assembly) is tightened to the specified torque.
The yaw rate and acceleration sensor (airbag sensor with ECU assembly) is not installed in a tilted position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
Check the yaw rate and acceleration sensor output value displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Lateral G | Lateral G | Min.: -25.105 m/s2 Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2 Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and rearward G | Min.: -25.105 m/s2 Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
| Yaw Rate Sensor Value | Yaw rate sensor | Min.: -128°/s Max.: 127°/s |
Vehicle stopped: 0°/s Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Tester Display |
|---|
| Lateral G |
| Forward and Rearward G |
| Yaw Rate Sensor Value |
The yaw rate and acceleration sensor output value is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
NG