Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C137BA2  Brake System Control Module "A" System Voltage System Voltage Low  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the No. 2 skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits operation of ABS, brake assist, regenerative brake cooperative control, etc.

This DTC is stored when the +BS, IG1 or IG2 terminal voltage meets one of the DTC detection conditions due to a malfunction in the power supply or charging circuit such as the battery or DC/DC converter circuit, etc.

This DTC is cleared when the voltage at terminal +BS, IG1 and IG2 returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C137BA2 Brake System Control Module "A" System Voltage System Voltage Low Any of the following is detected:
·

When the voltage at terminal +BS is less than 8.5 V, the master cylinder pressure sensor is invalid for 10 seconds or more.

·

When the voltage at terminal +BS is less than 8.5 V, the brake pedal stroke sensor assembly is invalid for 10 seconds or more.

·

When the +BS terminal voltage is below 9.5 V, the power source voltage for all speed sensors is continuously low for 60 seconds or more.

·

When the vehicle speed is 3 km/h (2 mph) or more, the voltage at terminal IG1 or terminal IG2 is excessively low for 10 seconds or more.

·

When the +BS terminal voltage is below 9.5 V and the solenoid relay is ON, the relay contact is OFF continuously for 1.22 seconds or more.

·

When the +BS terminal voltage is below 9.5 V, motor fail-safe relay overcurrent continues for 1.05 seconds or more.


·

Wire harness and connector

·

Backup boost converter circuit*

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

*: w/ Stop and Start System


C137BA2 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7
Diagnosis Condition When the voltage at terminal +BS is less than 8.5 V ○ ○ - - - - -
When the +BS terminal voltage is below 9.5 V - - ○ - - - ○
When the vehicle speed is 3 km/h (2 mph) or more - - - ○ ○ - -
When the +BS terminal voltage is below 9.5 V and the solenoid relay is ON - - - - - ○ -
Malfunction Status The master cylinder pressure sensor is invalid ○ - - - - - -
The brake pedal stroke sensor assembly is invalid - ○ - - - - -
The power source voltage for all speed sensors is continuously low - - ○ - - - -
The voltage at terminal IG1 is excessively low - - - ○ - - -
The voltage at terminal IG2 is excessively low - - - - ○ - -
The relay contact is OFF continuously - - - - - ○ -
Motor fail-safe relay overcurrent continues - - - - - - ○
Detection Time 10 seconds or more. 10 seconds or more. 60 seconds or more. 10 seconds or more. 10 seconds or more. 1.22 seconds or more. 1.05 seconds or more.
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C457035E01
5.031,0.698 5.479,1.073 0.448,0.375 10 false +BS 5.021,3.281 5.479,3.479 0.458,0.198 10 false GND1 4.74,0.469 5.052,0.667 0.313,0.198 10 false 14 4.802,3.188 5.135,3.354 0.333,0.167 10 false 1 4.844,4.042 6.76,4.479 1.917,0.438 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 4.844,3.875 5.26,4.052 0.417,0.177 10 false B20 3.427,0.76 4.156,1.01 0.729,0.25 10 false ABS NO. 2 2.063,0.542 3.896,0.99 1.833,0.448 10 false from Battery 1.948,1.844 2.927,2.021 0.979,0.177 10 false from IG Circuit 4.75,1.719 5.083,1.917 0.333,0.198 10 false 45 5.031,1.958 5.479,2.24 0.448,0.281 10 false IG1 3.292,2.677 4.354,3.01 1.063,0.333 10 false ENG-IGP NO. 2 5.01,2.615 5.458,2.896 0.448,0.281 10 false IG2 4.74,2.375 5.073,2.573 0.333,0.198 10 false 15 3.24,2.01 4.302,2.344 1.063,0.333 10 false ECU-IGR NO. 3 1.948,2.49 2.906,2.688 0.958,0.198 10 false from IG Circuit 6.01,1.656 6.323,1.854 0.313,0.198 10 false IC 1.813,0.979 2.125,1.177 0.313,0.198 10 false 23 1.375,1.125 1.99,1.323 0.615,0.198 10 false IG31 0.063,1.51 0.521,1.708 0.458,0.198 10 false I57 0.052,1.667 1.958,1.854 1.906,0.188 10 false Engine Stop and Start ECU*1 4.188,1.031 4.448,1.229 0.26,0.198 10 false *1 4.198,1.729 4.458,1.927 0.26,0.198 10 false *2 0.271,3.74 2.177,3.927 1.906,0.188 10 false *1: w/ Stop and Start System 0.271,4.073 2.177,4.26 1.906,0.188 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

B

8.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-45 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-15 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-14 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-1 (GND1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CLEAR DTC
a.

Reconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
C137BA2 is not output A
C137BA2 is output B



A

B

8.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-45 (IG1) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)

NG

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

9.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-15 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-14 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-1 (GND1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CLEAR DTC
a.

Reconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

13.RECONFIRM DTC
13.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
C137BA2 is not output A
C137BA2 is output B



A

B