Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL
RM38G0E _51 Engine / Hybrid System _101207 1GR-FE ENGINE MECHANICAL _0469486 REAR CRANKSHAFT OIL SEAL A

1GR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A487698N02
4.479,2.344 5.177,2.563 0.698,0.219 4.438,2.302 5.229,2.604 0.792,0.302 4.521,5.417 4.813,5.417 4.813,5.417 5.01,4.698 true 3.135,1.99 2.906,1.99 2.906,1.99 2.688,2.521 true 2.75,4.146 3.042,4.146 3.042,4.146 3.24,3.427 true 1.333,3.604 1.625,3.604 1.625,3.604 1.823,2.885 true 1.99,1.594 1.76,1.594 1.76,1.594 1.51,2.385 true 4.219,2.469 3.99,2.469 3.99,2.469 3.656,3.542 true 4.354,5.292 4.677,5.646 0.323,0.354 18 false 3 3.5,1.875 3.823,2.229 0.323,0.354 18 false 2 2.5,1.469 2.823,1.823 0.323,0.354 18 false 1 2.344,1.5 2.667,1.854 0.323,0.354 10 false ● 1.177,3.531 1.5,3.885 0.323,0.354 10 false *1 2.583,4.073 2.906,4.427 0.323,0.354 10 false *2 3.719,3.479 4.042,3.833 0.323,0.354 10 false x 8 4.271,2.375 4.583,2.625 0.313,0.25 10 false ★ 4.521,2.385 5.333,2.635 0.813,0.25 8 false 83 (846, 61)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR CRANKSHAFT OIL SEAL 11381A (Click here) - -
2 DRIVE PLATE AND RING GEAR SUB-ASSEMBLY 32101 (Click here) - -
3 AUTOMATIC TRANSMISSION ASSEMBLY 35000 - - -

*1 FRONT DRIVE PLATE SPACER *2 REAR DRIVE PLATE SPACER
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) ● Non-reusable part
★ Precoated part
V100135

MP grease
V100136

Adhesive 1324 - -

PROCEDURE

Hide 11381A 1.INSTALL REAR CRANKSHAFT OIL SEAL

a.
A487700E01
5.854,1.594 5.583,1.594 5.583,1.594 5.583,1.031 true 5.896,1.5 6.229,1.677 0.333,0.177 10 true SST 0.813,0.031 1.25,0.354 0.438,0.323 18 false i 3.896,0.031 4.177,0.292 0.281,0.26 18 false ii

i.

Apply MP grease to the lip of a new rear crankshaft oil seal.


ii.

Using SST and a hammer, tap in the rear crankshaft oil seal until its surface is flush with the rear oil seal retainer edge.

SST
09223-78010  

NOTICE:
·

Keep the lip of the rear crankshaft oil seal free from foreign matter.

·

Do not tap the rear crankshaft oil seal at an angle.





Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A488515C01
2.323,1.313 2.323,0.917 true 1.771,1.208 1.99,0.927 1.99,0.927 2.667,0.927 true 4.521,0.948 4.875,0.948 true 5.167,0.917 5.521,0.917 true 5.823,0.792 6.177,0.792 true 4.365,0.875 4.615,1.198 0.25,0.323 10 false *1 5.01,0.833 5.302,1.052 0.292,0.219 10 false *2 5.656,0.708 5.969,0.885 0.313,0.177 10 false *3 0.375,0.833 0.74,1.094 0.365,0.26 18 true i, ii 6.573,0.688 6.823,0.917 0.25,0.229 10 false *a 4.031,0.365 4.385,0.656 0.354,0.292 18 true iii 0.406,3.927 0.771,4.188 0.365,0.26 18 true iv 4.031,3.948 4.396,4.208 0.365,0.26 18 false v 2.698,0.833 3.021,1.01 0.323,0.177 10 true SST 5.25,4.021 5.354,4.198 0.104,0.177 10 true 1 5.573,5.271 5.677,5.448 0.104,0.177 10 true 2 5.979,4.531 6.083,4.708 0.104,0.177 10 true 3 4.813,4.823 4.917,5 0.104,0.177 10 true 4 5.708,4.135 5.813,4.313 0.104,0.177 10 true 5 5.104,5.229 5.208,5.406 0.104,0.177 10 true 6 5.927,4.958 6.031,5.135 0.104,0.177 10 true 7 4.854,4.365 4.958,4.542 0.104,0.177 10 true 8
*1 Front Drive Plate Spacer *2 Drive Plate and Ring Gear Sub-assembly
*3 Rear Drive Plate Spacer - -
*a Automatic Transmission Side - -


i.

Using SST, hold the crankshaft pulley.

SST
09213-54015  (91651-60855)
09330-00021  


ii.

Clean the bolts and their installation holes.


iii.

Install the front drive plate spacer, drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.

HINT:

As the front drive plate spacer, the drive plate and ring gear sub-assembly, and the rear drive plate spacer are not reversible, be sure to install them in the direction shown in the illustration.



iv.

Apply adhesive to 2 or 3 threads at the end of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



v.

Uniformly install and tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
83 N*m (846 kgf*cm, 61 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.