Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY
RM38G0E _52 Drivetrain _100436 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0468725 AUTOMATIC TRANSMISSION ASSEMBLY A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C458791N01
0.333,1.667 1.083,1.833 0.75,0.167 5.583,5.417 6.333,5.583 0.75,0.167 3.583,0.917 4.25,1.083 0.667,0.167 5.25,1.667 5.917,1.833 0.667,0.167 4.917,5.167 5.583,5.333 0.667,0.167 1.667,0.5 2.333,0.667 0.667,0.167 4.917,2.083 5.333,2.083 false 5.25,4.833 5.417,4.833 5.417,4.833 5.417,4.375 false 1.75,1.667 1.75,1.333 1.75,1.333 2,1.333 false 1.583,4.438 1.583,4.833 1.583,4.833 1.833,4.833 false 6.167,3.708 6.167,3.167 6.167,3.167 6.333,3.167 false 0.635,2.094 0.083,1.75 0.083,1.75 0.333,1.75 false 0.75,2.833 1.083,2.833 1.083,2.833 1.125,2.5 false 3.219,1 3.583,1 false 4.844,1.75 5.25,1.75 false 5.583,5.25 5.917,5.25 5.917,5.25 5.917,4.625 false 1.417,1.469 1.417,0.583 1.417,0.583 1.667,0.583 false 3.396,1.563 3.583,1.417 3.583,1.417 3.75,1.417 false 6.333,5.5 6.583,5.5 6.583,5.5 6.583,4.01 false 3.833,1.25 4.333,1.833 0.5,0.583 18 false 4 5.417,1.917 5.917,2.5 0.5,0.583 18 false 4 5.042,4.677 5.542,5.26 0.5,0.583 18 false 4 2.385,1.146 2.76,1.563 0.375,0.417 18 false 3 2.177,4.677 3.25,5.25 1.073,0.573 18 false 1 0.563,2.688 1.063,3.188 0.5,0.5 18 false 2 6.417,3 6.75,3.417 0.333,0.417 18 false 2 0.396,1.667 1.229,1.833 0.833,0.167 8 false 30 (306, 22) 5.667,5.417 6.5,5.583 0.833,0.167 8 false 13 (133, 10) 1.479,1.333 1.813,1.5 0.333,0.167 10 false x 2 3.625,0.917 4.458,1.083 0.833,0.167 8 false 10 (102, 7) 5.302,1.667 6.135,1.833 0.833,0.167 8 false 10 (102, 7) 4.979,5.167 5.813,5.333 0.833,0.167 8 false 10 (102, 7) 1.719,0.5 2.552,0.667 0.833,0.167 8 false 12 (122, 9)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 TORQUE CONVERTER ASSEMBLY 32000 (Click here) - -
2 EXHAUST SENSOR CLAMP BRACKET 8946A - - -
3 NO. 1 TRANSMISSION CONTROL CABLE BRACKET 33823 (Click here) - -
4 WIRE HARNESS CLAMP BRACKET - - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

C459003N01
2.667,2.875 3.417,3.042 0.75,0.167 2.5,5.417 3.25,5.583 0.75,0.167 2.458,5.375 3.292,5.625 0.833,0.25 2.625,2.833 3.458,3.083 0.833,0.25 5.417,2.833 6.167,3 0.75,0.167 3.417,4.417 3.417,4.917 3.417,4.917 3.75,4.917 false 2.583,2.323 2.583,1.917 2.583,1.917 2.833,1.917 false 4.167,1 4.167,0.333 4.167,0.333 4.5,0.333 false 5.75,3.667 6,3.333 6,3.333 6.25,3.333 false 2.25,5.198 2.25,5.5 2.25,5.5 2.5,5.5 false 2.302,2.958 2.667,2.958 false 5.01,2.917 5.417,2.917 false 4.167,4.75 5.333,5.167 1.167,0.417 18 false 6 2.896,1.771 3.396,2.188 0.5,0.417 18 false 8 4.917,0.167 5.417,0.583 0.5,0.417 18 false 7 6.667,3.188 7,3.604 0.333,0.417 18 false 5 2.125,3.031 2.583,3.229 0.458,0.198 10 false x 5 2.375,5.104 2.833,5.302 0.458,0.198 10 false x 4 2.719,2.875 3.552,3.042 0.833,0.167 8 false 71 (724, 52) 2.573,5.417 3.406,5.583 0.833,0.167 8 false 37 (377, 27) 4.875,3 5.333,3.198 0.458,0.198 10 false x 5 5.479,2.833 6.229,3 0.75,0.167 8 false 40 (408, 30)

Procedure Part Name Code
Z101186

Z101188

Z101187

5 TRANSFER ASSEMBLY 36100 (Click here) - -
6 AUTOMATIC TRANSMISSION ASSEMBLY 35000 (Click here) - -
7 ENGINE WIRE 82121 (Click here) - -
8 TRANSFER BREATHER HOSE SUB-ASSEMBLY 36407 - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

Clutch Spline Grease - -

C458206N01
5.083,5.5 5.833,5.667 0.75,0.167 5.333,4.583 6.083,4.75 0.75,0.167 5.833,1.917 6.583,2.083 0.75,0.167 2.083,0.375 2.917,0.542 0.833,0.167 1.833,0.083 2.833,0.25 1,0.167 0.167,0.083 1.167,0.25 1,0.167 1,1.917 1.833,2.083 0.833,0.167 3.583,0.583 4.5,0.917 0.917,0.333 3.542,0.542 4.542,0.958 1,0.417 5.292,4.542 6.125,4.792 0.833,0.25 5.042,5.458 5.875,5.708 0.833,0.25 2.667,3.833 3.417,4 0.75,0.167 1.083,2.167 1.833,2.333 0.75,0.167 1.042,2.125 1.875,2.375 0.833,0.25 6.167,3.583 6,3.583 6,3.583 5.833,4.167 false 1.833,1.75 1.583,1.75 1.583,1.75 1.583,1.469 false 6,1.333 5.833,1.333 5.833,1.333 5.563,1.646 false 2.5,4.417 2.75,4.417 2.75,4.417 2.75,4.188 false 1.083,2.25 0.5,2.25 0.5,2.25 0.5,3 false 4.667,4.083 4.833,3.781 4.833,3.781 5.083,3.781 false 5.396,5.167 5.833,5.167 false 5.083,5.583 4.708,5.583 4.708,5.583 4.708,5.438 false 5.333,4.667 4.969,4.667 4.969,4.667 4.969,4.552 false 5.448,2 5.833,2 false 1.833,0.167 1.552,0.167 1.552,0.167 1.552,0.75 false 1.781,0.458 2.083,0.458 false 1.167,0.167 1.333,0.167 1.333,0.167 1.083,0.583 false 0.75,0.781 0.75,2 0.75,2 1,2 false 1.833,3.917 2.135,3.917 2.135,3.917 2.135,3.542 false 2.927,1.125 3.333,0.75 3.333,0.75 3.583,0.75 false 2.979,1.271 3.333,0.75 false 3.417,3.917 3.667,3.917 3.667,3.917 4.333,4.333 false 2.979,2.167 3.229,1.917 3.229,1.917 3.396,1.917 false 6.542,3.365 7.042,3.781 0.5,0.417 18 false 17 2.26,1.552 2.927,2.052 0.667,0.5 18 false 16 6.031,1.177 6.698,1.677 0.667,0.5 18 false 15 2.156,4.271 2.823,4.771 0.667,0.5 18 false 14 2.271,2.052 2.938,2.552 0.667,0.5 18 false 12 5.875,5 6.542,5.5 0.667,0.5 18 false 11 5.406,3.563 6.073,4.063 0.667,0.5 18 false 9 5.042,4.406 5.375,4.573 0.333,0.167 10 false x 4 4.802,5.292 5.135,5.458 0.333,0.167 10 false x 4 0.5,3.083 0.833,3.25 0.333,0.167 10 false *a 5.156,5.5 6.073,5.667 0.917,0.167 8 false 37 (377, 27) 5.396,4.583 6.313,4.75 0.917,0.167 8 false 59 (602, 44) 5.917,1.917 6.833,2.083 0.917,0.167 8 false 10 (102, 7) 2.146,0.375 3.063,0.542 0.917,0.167 8 false 13.5 (138, 10) 1.052,1.917 1.969,2.083 0.917,0.167 8 false 13.5 (138, 10) 1.875,0.083 2.958,0.25 1.083,0.167 8 false 5.5 (56, 49 in.*lbf) 0.219,0.083 1.302,0.25 1.083,0.167 8 false 5.5 (56, 49 in.*lbf) 1.5,3.75 2.167,4.25 0.667,0.5 18 false 13 3.667,0.583 4.583,0.75 0.917,0.167 8 false 34 (347, 25) 3.667,0.75 4.583,0.917 0.917,0.167 8 false 29.1 (297, 21)* 4.417,4.396 4.75,4.563 0.333,0.167 10 false x 4 3.583,4.604 3.917,4.771 0.333,0.167 10 false x 4 2.75,3.833 3.667,4 0.917,0.167 8 false 42 (428, 31) 1.167,2.167 2.083,2.333 0.917,0.167 8 false 48 (489, 35) 3.458,1.75 4.125,2.25 0.667,0.5 18 false 10

Procedure Part Name Code
Z101186

Z101188

Z101187

9 REAR ENGINE MOUNTING INSULATOR 12371A (Click here) - -
10 TRANSMISSION BREATHER HOSE ASSEMBLY - - - -
11 NO. 3 FRAME CROSSMEMBER ASSEMBLY - (Click here) - -
12 DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT - (Click here) - -
13 FLYWHEEL HOUSING SIDE COVER 11363A - - -
14 FLYWHEEL HOUSING UNDER COVER 11361J - - -
15 WIRE HARNESS CLAMP BRACKET - - - -
16 OIL COOLER TUBE - (Click here) - -
17 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -

*a BLACK: x 1
SILVER: x 5
- -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
* For use with union nut wrench - -

C458205N02
2,5.5 2.75,5.667 0.75,0.167 6.417,0.583 6.75,0.583 false 6.417,0.167 6.75,0.167 false 5.583,3.5 5.917,3.5 false 4.167,5.25 4.833,5.25 false 4.333,3.917 4.833,3.917 false 4.917,2.333 5.333,2.333 5.333,2.333 5.333,2.833 false 2,3.75 1.833,3.75 1.833,3.75 1.833,4.25 false 4.833,4.333 4.25,4.333 4.25,4.333 4.25,4.75 false 2.75,5.583 3.104,5.583 false 6.417,1 6.75,1 false 5.667,0.417 6.667,0.917 1,0.5 18 false 23, 24 5.667,0 6.667,0.5 1,0.5 18 false 25, 26 6,3.333 6.667,3.833 0.667,0.5 18 false 18 5.25,5.083 5.917,5.583 0.667,0.5 18 false 27 3.25,5.5 3.583,5.667 0.333,0.167 10 false x 4 4.917,3.75 5.583,4.25 0.667,0.5 18 false 19 4.583,2.167 5.25,2.667 0.667,0.5 18 false 20 2.083,3.583 2.75,4.083 0.667,0.5 18 false 21 4.917,4.167 5.583,4.667 0.667,0.5 18 false 22 2.063,5.5 2.813,5.667 0.75,0.167 8 false 50 (510, 37) 5.667,0.833 6.667,1.333 1,0.5 18 false 28, 29

Procedure Part Name Code
Z101186

Z101188

Z101187

18 STARTER ASSEMBLY 28100 - - -
19 EXHAUST MANIFOLD ASSEMBLY RH 17140 - - -
20 EXHAUST MANIFOLD ASSEMBLY LH 17150 - - -
21 REAR PROPELLER SHAFT ASSEMBLY 37110F - - -
22 FRONT PROPELLER SHAFT ASSEMBLY 37140 - - -
23 ADD TRANSFER OIL - - (Click here) -
24 ADD AUTOMATIC TRANSMISSION FLUID - - (Click here) -
25 INSPECT SHIFT LEVER POSITION - (Click here) - -
26 INSPECT FOR EXHAUST GAS LEAK - (Click here) - -
27 OIL PAN PROTECTOR ASSEMBLY 51440 (Click here) - -
28 RESET MEMORY - - - (Click here)
29 ATF THERMAL DEGRADATION ESTIMATE RESET - - - (Click here)

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C456859C01
2,0.75 2.167,0.75 2.167,0.75 2.583,1.25 true 2.583,2.417 2.833,2.417 2.833,2.417 3.167,2 true 1.917,0.031 2.25,0.448 0.333,0.417 18 false i 4.5,0.615 4.667,0.781 0.167,0.167 10 false *a 4.75,1.333 4.917,1.5 0.167,0.167 10 false *b 4.521,0.167 4.688,0.333 0.167,0.167 10 false A 1.833,0.667 2,0.833 0.167,0.167 10 false *a 2.417,2.333 2.583,2.5 0.167,0.167 10 false *b
*a Engine Assembly Surface *b Drive Plate and Ring Gear Sub-assembly Surface


i.

Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transmission assembly contact surface of the engine assembly (*a) and the torque converter assembly contact surface of the drive plate and ring gear sub-assembly (*b).



b.
C456860C01
1.115,0.344 1.5,0.167 1.5,0.167 1.667,0.167 true 1.115,0.5 1.5,0.167 true 0.396,0.042 0.813,0.542 0.417,0.5 18 false i 3.854,0.042 4.271,0.542 0.417,0.5 18 false ii 2.042,1.938 2.458,2.438 0.417,0.5 18 false iii 1.708,0.083 1.875,0.25 0.167,0.167 10 false *a 6.5,0.833 6.667,1 0.167,0.167 10 false *1 4.646,2.771 4.813,2.938 0.167,0.167 10 false *1
*1 Front Oil Pump Oil Seal - -
*a Matchmark - -


i.

Align the matchmark on the automatic transmission case sub-assembly with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:

Install the torque converter assembly to the input shaft while keeping it horizontal.



ii.

Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




iii.

Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the automatic transmission case sub-assembly and insert the key of the torque converter assembly into the groove of the oil pump drive gear.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.





c.
C456861N01
1.875,0.021 2.292,0.521 0.417,0.5 18 false i 4.365,0.583 4.531,0.75 0.167,0.167 10 false B

i.

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard Distance:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transmission assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.





Hide 8946A 2.INSTALL EXHAUST SENSOR CLAMP BRACKET

a.
C458212C01
0,0 0,0 false
V100135

Bolt A
V100136

Bolt B


Torque:
for Bolt A : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for Bolt B : 30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:

It is not necessary to remove the exhaust sensor clamp bracket unless it is being replaced.



Hide 33823 3.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C458801C01
1.833,0 2.083,0.333 0.25,0.333 18 false i
V100135

Bolt A
V100136

Bolt B


i.

Install the No. 1 transmission control cable bracket to the automatic transmission assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

HINT:
·

Tightening order: Temporarily install bolt A and B → Tighten bolt A → Tighten bolt B

·

It is not necessary to remove the No. 1 transmission control cable bracket unless it is being replaced.





Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

It is not necessary to remove the wire harness clamp brackets unless they are being replaced.


Hide 36100 5.INSTALL TRANSFER ASSEMBLY

Z101186

Click here(Click here)

Hide 35000 6.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C456862C01
1.167,0.917 1.5,0.917 true 1.802,0.958 2.083,1.167 2.083,1.167 2.25,1.167 true 1,0.052 1.333,0.49 0.333,0.438 18 false i 3.479,0.052 3.813,0.49 0.333,0.438 18 false ii 2.229,1.969 2.563,2.406 0.333,0.438 18 false iii 1,0.833 1.167,1 0.167,0.167 10 false *1 2.25,1.083 2.417,1.25 0.167,0.167 10 false *2
*1 Crankshaft *2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease
V100136

Knock Pin
V100137

Bolt A
V100138

Bolt B


i.

Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz.)



ii.

Confirm that the 2 knock pins are on the surface of the engine block that contacts the automatic transmission assembly.


iii.

Keeping the engine and automatic transmission assembly horizontal, align the knock pins with the holes on the automatic transmission assembly and install the 9 bolts shown in the illustration.

Torque:
for Bolt A (17 mm head) : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for Bolt B (14 mm head) : 37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:
·

Do not use excessive force when installing the automatic transmission assembly.

·

Check that the torque converter assembly rotates.

·

Make sure that the wire harness or other similar items are not pinched between the contact surfaces.

·

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.





Hide 82121 7.CONNECT ENGINE WIRE

a.
C459792C01
0.375,0 0.875,0.417 0.5,0.417 18 false i, ii
V113147

Push Up - -


i.

Attach the clamp.


ii.

Connect the 8 engine wire connectors to the automatic transmission assembly with transfer assembly.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.




Hide 36407 8.INSTALL TRANSFER BREATHER HOSE SUB-ASSEMBLY

Hide 12371A 9.INSTALL REAR ENGINE MOUNTING INSULATOR

Z101186

Click here(Click here)

Hide 10.INSTALL TRANSMISSION BREATHER HOSE ASSEMBLY

Hide 11.INSTALL NO. 3 FRAME CROSSMEMBER ASSEMBLY

Z101186

Click here(Click here)

Hide 12.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.
C456848N01
1.833,0 2.25,0.417 0.417,0.417 18 false i

i.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install the drive plate and torque converter assembly setting bolts while holding the crankshaft pulley set bolt with a wrench.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)

NOTICE:

Install the black colored bolt first, and then the remaining 5 silver colored bolts.




Hide 11363A 13.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 11361J 14.INSTALL FLYWHEEL HOUSING UNDER COVER

Hide 15.CONNECT WIRE HARNESS CLAMP BRACKET

Hide 16.CONNECT OIL COOLER TUBE

a.
C456864C01
0.365,0 1.115,0.417 0.75,0.417 18 false i - iv 1.49,0.927 1.656,1.094 0.167,0.167 10 true *a
*a Torque Wrench Fulcrum Length - -
V100135

Flare Nut
V100136

Bolt A
V100137

Bolt B - -


i.

Connect the ends of the 2 oil cooler tubes to the automatic transmission assembly by hand.


ii.

Install the 2 oil cooler tube clamps to the automatic transmission assembly and engine assembly with the 2 bolts labeled A.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)

HINT:

It is not necessary to remove the oil cooler tube clamps unless they are being replaced.



iii.

Connect the 2 oil cooler tubes to the 2 oil cooler tube clamps with the 2 bolts labeled B.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


iv.

Using a 17 mm union nut wrench, tighten the 2 oil cooler tubes.

Torque:
Specified tightening torque : 34 N*m (347 kgf*cm, 25 ft.*lbf)

HINT:
·

It is not necessary to remove the oil cooler tube clamp unless it is being replaced.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 29.1 N*m (297 kgf*cm, 21 ft.*lbf)





Hide 33820B 17.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Z101186

Click here(Click here)

Hide 28100 18.INSTALL STARTER ASSEMBLY

Click hereEngine / Hybrid System>1GR-FE (STARTING)>STARTER>INSTALLATION

HINT:

Install the under cover after completing the adjustment and inspection procedure.


Hide 17140 19.INSTALL EXHAUST MANIFOLD ASSEMBLY RH

Click hereEngine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>EXHAUST MANIFOLD>INSTALLATION

HINT:

Install the under cover after completing the adjustment and inspection procedure.


Hide 17150 20.INSTALL EXHAUST MANIFOLD ASSEMBLY LH

Click hereEngine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>EXHAUST MANIFOLD>INSTALLATION

HINT:

Install the under cover after completing the adjustment and inspection procedure.


Hide 37110F 21.INSTALL REAR PROPELLER SHAFT ASSEMBLY

Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY>INSTALLATION

HINT:

Install the under cover after completing the adjustment and inspection procedure.


Hide 37140 22.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY>INSTALLATION

HINT:

Install the under cover after completing the adjustment and inspection procedure.


Hide 23.ADD TRANSFER OIL

Z101186

Click here(Click here)

Hide 25.INSPECT SHIFT LEVER POSITION

Z101186

Click here(Click here)

Hide 51440 27.INSTALL OIL PAN PROTECTOR ASSEMBLY

a.
C458203C01
1.75,0 2,0.417 0.25,0.417 18 false i
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C - -


i.

Install the oil pan protector assembly to the vehicle body with the 4 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt A, B and C → Tighten bolt A → Tighten bolt B → Tighten bolt C




Hide 28.RESET MEMORY

Z101186

Click here(Click here)

Hide 29. ATF THERMAL DEGRADATION ESTIMATE RESET

Z101186

NOTICE:

Approximately 50% or more of the ATF has been replaced during a repair of the transmission or a similar operation.

Click here(Click here)