Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM38G0E _51 Engine / Hybrid System _101207 1GR-FE ENGINE MECHANICAL _0469490 CYLINDER BLOCK G

1GR-FE ENGINE MECHANICAL  CYLINDER BLOCK  INSPECTION  


PROCEDURE

Hide 11401 1.CLEAN CYLINDER BLOCK SUB-ASSEMBLY

a.

Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block sub-assembly.


b.

Using a soft brush and solvent, thoroughly clean the cylinder block sub-assembly.

NOTICE:

If the cylinder is washed at high temperatures, the cylinder liner sticks out beyond the cylinder block sub-assembly. Always wash the cylinder block sub-assembly at a temperature of 45°C (113°F) or less.



Hide 2.INSPECT CYLINDER BLOCK FOR FLATNESS

a.
A326730

Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder head gasket.

Maximum warpage:

0.05 mm (0.00197 in.)


If the warpage is more than the maximum, replace the cylinder block sub-assembly.


Hide 3.INSPECT CYLINDER BORE

a.
A328417C01
1.969,3 2.385,2.469 2.385,2.469 2.573,2.469 false 1.719,2.781 2.135,2.25 2.135,2.25 2.323,2.25 false 0.375,2.906 0.688,3.063 0.313,0.156 10 false *a 2.375,2.167 2.688,2.323 0.313,0.156 10 false *b 2.646,2.406 2.958,2.563 0.313,0.156 10 false *c 0.969,3.927 1.281,4.083 0.313,0.156 10 false *d 2.313,3.25 2.625,3.406 0.313,0.156 10 false *e 1.635,3.948 1.948,4.104 0.313,0.156 10 false B 1.625,3.656 1.938,3.813 0.313,0.156 10 false A
*a Engine Front
*b Thrust Direction
*c Axial Direction
*d Center
*e 10 mm (0.394 in.)


Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.

Reference diameter (new parts):

94.000 to 94.012 mm (3.7008 to 3.7013 in.)


Maximum diameter:

94.132 mm (3.7060 in.)


Measurement position (A):

10 mm (0.394 in.)


If the diameter is more than the maximum, replace the cylinder block sub-assembly.


Hide 4.CLEAN PISTON WITH PIN SUB-ASSEMBLY

a.

Clean the piston.

i.

Using a gasket scraper, remove the carbon from the piston top.


ii.

Using a groove cleaning tool or broken ring, clean the piston ring grooves.


iii.

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.




Hide 5.INSPECT PISTON DIAMETER

a.
A221395C01
2.771,1.729 3.083,1.927 0.313,0.198 10 false *a
*a 9.6 mm (0.378 in.)


Using a micrometer, measure the piston diameter at a position that is 9.6 mm (0.378 in.) from the bottom of the piston.

Reference value (new parts):

93.961 to 93.991 mm (3.6992 to 3.7004 in.)



Hide 6.INSPECT PISTON OIL CLEARANCE

a.

Subtract the piston diameter measurement from the cylinder bore diameter measurement.

Reference value (new parts):

0.009 to 0.051 mm (0.000354 to 0.00201 in.)


Maximum oil clearance:

0.110 mm (0.00433 in.)


If the oil clearance is more than the maximum, replace all 6 pistons. If necessary, replace the cylinder block.


Hide 7.INSPECT RING GROOVE CLEARANCE

a.

Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

Standard Ring Groove Clearance:
Item Specified Condition
No. 1 compression ring 0.02 to 0.07 mm (0.000787 to 0.00276 in.)
No. 2 compression ring 0.02 to 0.06 mm (0.000787 to 0.00236 in.)
Oil ring 0.07 to 0.15 mm (0.00276 to 0.00591 in.)


If the clearance is not as specified, replace the piston with pin sub-assembly.


Hide 8.INSPECT PISTON RING END GAP

a.

Insert the piston ring into the cylinder bore.


b.

Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block sub-assembly.


c.

Using a feeler gauge, measure the end gap.

Standard End Gap:
Item Specified Condition
No. 1 compression ring 0.22 to 0.32 mm (0.00866 to 0.0126 in.)
No. 2 compression ring 0.35 to 0.45 mm (0.0138 to 0.0177 in.)
Oil ring (side rail) 0.10 to 0.40 mm (0.00394 to 0.0157 in.)


Maximum End Gap:
Item Specified Condition
No. 1 compression ring 1.0 mm (0.0394 in.)
No. 2 compression ring 1.1 mm (0.0433 in.)
Oil ring (side rail) 1.0 mm (0.0394 in.)


If the end gap is more than the maximum, replace the piston ring. If the end gap is more than the maximum even with a new piston ring, rebore all 6 cylinders or replace the cylinder block sub-assembly.


Hide 9.INSPECT PISTON PIN OIL CLEARANCE

a.
A221396C03
1.917,1.479 2.167,1.854 2.167,1.854 2.396,1.854 true 2.125,1.25 2.729,1.25 true 1.948,3.76 2.26,3.438 2.26,3.438 2.49,3.438 true 0.875,4.313 1.479,4.313 true 2.438,1.75 2.76,2.021 0.323,0.271 10 false *a 2.75,1.156 3.073,1.427 0.323,0.271 10 false *b 2.542,3.333 2.865,3.604 0.323,0.271 10 false *a 0.708,4.229 1.031,4.5 0.323,0.271 10 false *b
*a Front Mark
*b Inside Diameter Mark


Check each mark on the piston and connecting rod sub-assembly.


b.
A221397

Using a caliper gauge, measure the inside diameter of the piston pin hole.

Standard Piston Pin Hole Inside Diameter:
Item Specified Condition
Mark A 22.001 to 22.004 mm (0.86618 to 0.86630 in.)
Mark B 22.005 to 22.007 mm (0.86634 to 0.86642 in.)
Mark C 22.008 to 22.010 mm (0.86645 to 0.86653 in.)



c.
A146331C08
1.219,2.417 1.406,2.635 0.188,0.219 10 false *a 1.417,1.479 1.646,1.708 0.229,0.229 10 false *b 1.677,2.979 1.906,3.198 0.229,0.219 10 false *b
*a 28 mm (1.10 in.)
*b 5.0 mm (0.197 in.)


Using a micrometer, measure the piston pin diameter.

Standard Piston Pin Diameter:
Item Specified Condition
Mark A 21.997 to 22.000 mm (0.86602 to 0.86614 in.)
Mark B 22.001 to 22.003 mm (0.86618 to 0.86626 in.)
Mark C 22.004 to 22.006 mm (0.86630 to 0.86638 in.)



d.

Using a caliper gauge, measure the inside diameter of the connecting rod bush.

Standard Bush Inside Diameter:
Item Specified Condition
Mark A 22.005 to 22.008 mm (0.86634 to 0.86645 in.)
Mark B 22.009 to 22.011 mm (0.86649 to 0.86657 in.)
Mark C 22.012 to 22.014 mm (0.86661 to 0.86669 in.)



e.

Subtract the piston pin diameter measurement from the piston pin hole diameter measurement.

Standard oil clearance:

0.001 to 0.007 mm (0.0000394 to 0.000276 in.)


Maximum oil clearance:

0.040 mm (0.00157 in.)


If the oil clearance is more than the maximum, replace the piston with pin sub-assembly.


f.

Subtract the piston pin diameter measurement from the bush inside diameter measurement.

Standard oil clearance:

0.005 to 0.011 mm (0.000197 to 0.000433 in.)


Maximum oil clearance:

0.050 mm (0.00197 in.)


If the oil clearance is more than the maximum, replace the connecting rod sub-assembly and piston with pin sub-assembly.


Hide 13411 10.INSPECT CRANKSHAFT

a.

Using a dial indicator, measure the runout at the center journal.

Maximum circle runout:

0.06 mm (0.00236 in.)


If the circle runout is more than the maximum, replace the crankshaft.


b.
A076059

Using a micrometer, measure the diameter of each main journal.

Standard diameter:

71.988 to 72.000 mm (2.8342 to 2.8346 in.)


If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.


c.

Check each main journal for taper and out-of-round as shown in the illustration.

Maximum taper and out-of-round:

0.02 mm (0.000787 in.)


If the taper and out-of-round is more than the maximum, replace the crankshaft.


d.
A076060

Using a micrometer, measure the diameter of each crank pin.

Standard diameter:

55.992 to 56.000 mm (2.2044 to 2.2047 in.)


If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.


e.

Check each crank pin for taper and out-of-round as shown in the illustration.

Maximum taper and out-of-round:

0.02 mm (0.000787 in.)


If the taper and out-of-round is more than the maximum, replace the crankshaft.


Hide 11.INSPECT CRANKSHAFT OIL CLEARANCE


b.

Place the crankshaft on the cylinder block sub-assembly.


c.

Install the crankshaft thrust washer.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>CYLINDER BLOCK>REASSEMBLY


d.
A224722C03
0.51,0.677 0.688,0.677 0.688,0.677 1.281,1.365 false 0.323,0.594 0.531,0.792 0.208,0.198 10 false *a
*a Plastigage


Lay a strip of Plastigage across each journal.

NOTICE:

Do not turn the crankshaft.



e.


g.
A221398C02
0.781,0.396 0.948,0.396 0.948,0.396 1.313,1.313 true 0.625,0.323 0.813,0.542 0.188,0.219 10 false *a
*a Plastigage


Measure the Plastigage at its widest point.

Standard oil clearance:

0.026 to 0.046 mm (0.00102 to 0.00181 in.)


Maximum clearance:

0.080 mm (0.00315 in.)


If the oil clearance is more than the maximum, replace the bearings. If necessary, replace the crankshaft.


h.
A221399C02
1.313,1.615 1.5,1.615 1.5,1.615 1.854,0.823 false 1.792,4.365 1.99,4.365 1.99,4.365 2.365,3.948 true 1.135,3.729 0.635,4.5 0.635,4.5 1.115,3.979 true 1.99,0.708 2.646,0.313 2.646,0.313 2.792,0.313 false 2.792,0.615 2.635,0.615 2.635,0.615 1.99,0.771 false 2.792,0.896 2.646,0.896 2.646,0.896 1.99,0.854 false 2.792,1.177 2.667,1.177 2.667,1.177 2,0.927 false 2.25,3.74 2.25,2.958 2.25,2.958 2.479,2.958 true 2.677,3.26 2.573,3.26 2.573,3.26 2.354,3.781 false 2.719,3.552 2.615,3.552 2.615,3.552 2.448,3.813 true 2.729,3.854 2.542,3.854 false 1.125,1.521 1.354,1.698 0.229,0.177 10 false *e 1.604,4.271 1.875,4.5 0.271,0.229 10 false *e 0.458,4.458 0.667,4.625 0.208,0.167 10 false *e 2.833,0.229 3.219,0.448 0.385,0.219 10 false *a 2.833,0.521 3.229,0.729 0.396,0.208 10 false *b 2.833,0.802 3.229,1.031 0.396,0.229 10 false *c 2.833,1.094 3.146,1.354 0.313,0.26 10 false *d 2.51,2.854 2.698,3.052 0.188,0.198 10 true *a 2.708,3.177 2.948,3.375 0.24,0.198 10 true *b 2.76,3.458 2.979,3.646 0.219,0.188 10 true *c 2.802,3.75 3.021,3.979 0.219,0.229 10 true *d
*a No. 1
*b No. 2
*c No. 3
*d No. 4
*e Number Mark


If replacing a bearing, replace it with one that has the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, and then refer to the table below for the appropriate bearing number. There are 5 sizes of standard bearings, marked "1", "2", "3", "4" and "5" accordingly.

New Bearing:
Item Specified Condition
Cylinder block main journal bore diameter (A)
+
Crankshaft main journal diameter (B)
0 to 5 6 to 11 12 to 17 18 to 23 24 to 28
Use bearing 1 2 3 4 5


EXAMPLE:

Cylinder block "11" (A) + Crankshaft "06" (B) = Total number 17 (Use bearing "3")

Cylinder Block Main Journal Bore Diameter (A):
Item Specified Condition
Mark 00 77.000 mm (3.03149 in.)
Mark 01 77.001 mm (3.03153 in.)
Mark 02 77.002 mm (3.03157 in.)
Mark 03 77.003 mm (3.03161 in.)
Mark 04 77.004 mm (3.03165 in.)
Mark 05 77.005 mm (3.03169 in.)
Mark 06 77.006 mm (3.03173 in.)
Mark 07 77.007 mm (3.03177 in.)
Mark 08 77.008 mm (3.03180 in.)
Mark 09 77.009 mm (3.03184 in.)
Mark 10 77.010 mm (3.03188 in.)
Mark 11 77.011 mm (3.03192 in.)
Mark 12 77.012 mm (3.03196 in.)
Mark 13 77.013 mm (3.03200 in.)
Mark 14 77.014 mm (3.03204 in.)
Mark 15 77.015 mm (3.03208 in.)
Mark 16 77.016 mm (3.03212 in.)


Crankshaft Main Journal Diameter (B):
Item Specified Condition
Mark 00 71.999 to 72.000 mm (2.83460 to 2.83464 in.)
Mark 01 71.998 to 71.999 mm (2.83456 to 2.83460 in.)
Mark 02 71.997 to 71.998 mm (2.83452 to 2.83456 in.)
Mark 03 71.996 to 71.997 mm (2.83448 to 2.83452 in.)
Mark 04 71.995 to 71.996 mm (2.83444 to 2.83448 in.)
Mark 05 71.994 to 71.995 mm (2.83440 to 2.83444 in.)
Mark 06 71.993 to 71.994 mm (2.83436 to 2.83440 in.)
Mark 07 71.992 to 71.993 mm (2.83433 to 2.83436 in.)
Mark 08 71.991 to 71.992 mm (2.83429 to 2.83433 in.)
Mark 09 71.990 to 71.991 mm (2.83425 to 2.83429 in.)
Mark 10 71.989 to 71.990 mm (2.83421 to 2.83425 in.)
Mark 11 71.988 to 71.989 mm (2.83417 to 2.83421 in.)


Standard Bearing Center Wall Thickness:
Item Specified Condition
Mark 1 2.488 to 2.491 mm (0.0980 to 0.0981 in.)
Mark 2 2.491 to 2.494 mm (0.0981 to 0.0982 in.)
Mark 3 2.494 to 2.497 mm (0.0982 to 0.0983 in.)
Mark 4 2.497 to 2.500 mm (0.0983 to 0.0984 in.)
Mark 5 2.500 to 2.503 mm (0.0984 to 0.0985 in.)




j.


Hide 13201 12.INSPECT CONNECTING ROD SUB-ASSEMBLY

a.
A132171

Using a rod aligner and feeler gauge, check the connecting rod sub-assembly alignment.

i.

Check for bend.

Maximum bend:

0.05 mm (0.00197 in.) per 100 mm (3.94 in.)


If the bend is more than the maximum, replace the connecting rod sub-assembly.


ii.
A132172

Check for twist.

Maximum twist:

0.15 mm (0.00591 in.) per 100 mm (3.94 in.)


If the twist is more than the maximum, replace the connecting rod sub-assembly.



Hide 13265 13.INSPECT CONNECTING ROD BOLT

a.

Check that there is no damage or deformation on the threads of the connecting rod bolt.

HINT:

If there is any damage or deformation, replace the connecting rod bolt.



b.
A210580C06
1.521,0.552 1.792,0.781 0.271,0.229 10 false *a
*a Measurement Area


Using a vernier caliper, measure the diameter of the connecting rod bolt in the area shown in the illustration.

Standard diameter:

7.2 to 7.3 mm (0.283 to 0.287 in.)


Minimum diameter:

7.0 mm (0.276 in.)


HINT:

Diameter measurements should be done at several points.


If the diameter is less than the minimum, replace the connecting rod bolt with a new one. Failure to do so may lead to engine damage.


Hide 11416 14.INSPECT CRANKSHAFT BEARING CAP SET BOLT

a.

Check that there is no damage or deformation on the threads of the crankshaft bearing cap set bolt.

HINT:

If there is any damage or deformation, replace the crankshaft bearing cap set bolt.



b.
A223293C03
1.458,1.635 2.042,1.979 0.583,0.344 10 false *b 1.229,0.688 1.406,0.854 0.177,0.167 10 false *a
*a Measuring Area
*b 60 mm (2.36 in.)


Using a vernier caliper, measure the thread outside diameter of the crankshaft bearing cap set bolt in the measuring area.

Standard diameter:

10.0 to 10.2 mm (0.394 to 0.402 in.)


If the diameter is less than the minimum, replace the crankshaft bearing cap set bolt. Failure to do so may lead to engine damage.


Hide 15708 15.INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A188915

Push the check valve with a pin to check if it is stuck. If stuck, replace the No. 1 oil nozzle sub-assembly.


b.

Push the check valve with a pin to check if it moves smoothly.

If it does not move smoothly, clean or replace the No. 1 oil nozzle sub-assembly.


c.
A190792E01
0.505,0.65 0.661,0.846 0.156,0.197 10 A 2.733,0.63 2.889,0.827 0.156,0.197 10 B 1.265,0.616 1.421,0.813 0.156,0.197 10 C

While covering A, blow air into B. Check that air does not leak through C. Perform the check again while covering B and blowing air into A.

If air leaks, clean or replace the No. 1 oil nozzle sub-assembly.


d.
A190793E01
0.502,0.68 0.661,0.859 0.159,0.179 10 A 2.696,0.7 2.855,0.879 0.159,0.179 10 B 1.163,0.77 1.322,0.949 0.159,0.179 10 C

Push the check valve while covering A, and blow air into B. Check that air passes through C. Perform the check again while covering B, pushing the check valve and blowing air into A.

If air does not pass through C, clean or replace the No. 1 oil nozzle sub-assembly.