Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0467431 TRANSFER SYSTEM C

JF2BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17A811  4WD/AWD Transfer Case Shift Motor Control Circuit Short to Ground  P17A812  4WD/AWD Transfer Case Shift Motor Control Circuit Short to Battery  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P17A811 4WD/AWD Transfer Case Shift Motor Control Circuit Short to Ground
Diagnosis Condition:
·

ignition switch ON

·

High-low shift motor is stopped or operated


Malfunction Status:
·

High-low shift motor drive circuit monitor voltage is less than malfunction detection voltage


Malfunction Time:
·

1 second or more


Number of Trips:
·

1 trip


·

Wire harness and connector

·

Transfer shift actuator assembly

·

4 wheel drive control ECU


Four Wheel Drive
P17A812 4WD/AWD Transfer Case Shift Motor Control Circuit Short to Battery
Diagnosis Condition:
·

ignition switch ON

·

High-low shift motor is stopped or operated


Malfunction Status:
·

High-low shift motor drive circuit monitor voltage exceeds malfunction detection voltage


Malfunction Time:
·

1 second or more


Number of Trips:
·

1 trip


·

Wire harness and connector

·

Transfer shift actuator assembly

·

4 wheel drive control ECU


Four Wheel Drive

DTC Detection Conditions: P17A811
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch ON ○ ○
High-low shift motor is stopped ○ -
High-low shift motor is operated - ○
Malfunction Status High-low shift motor drive circuit monitor voltage is less than malfunction detection voltage ○ ○
Detection Time 1 second or more 1 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: P17A812
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch ON ○ ○
High-low shift motor is stopped ○ -
High-low shift motor is operated - ○
Malfunction Status High-low shift motor drive circuit monitor voltage exceeds malfunction detection voltage ○ ○
Detection Time 1 second or more 1 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C456051E01
5.594,5.333 6.052,5.531 0.458,0.198 10 false HM1 5.583,4.656 6.042,4.854 0.458,0.198 10 false HM2 4.302,5.333 4.76,5.531 0.458,0.198 10 false HM1 4.271,4.656 4.729,4.854 0.458,0.198 10 false HM2 5.167,5.438 5.625,5.635 0.458,0.198 10 false C48 5.167,4.781 5.625,4.979 0.458,0.198 10 false C48 1.396,6.427 1.854,6.625 0.458,0.198 10 false B11 4.792,5.302 4.948,5.5 0.156,0.198 10 false 6 4.823,4.646 4.979,4.844 0.156,0.198 10 false 7 5.24,5.219 5.396,5.417 0.156,0.198 10 false 1 5.24,4.552 5.396,4.75 0.156,0.198 10 false 2 5.521,5.604 6.99,5.906 1.469,0.302 10 false High-Low Shift Actuator 5.656,3.771 6.854,4.302 1.198,0.531 10 false Center Differential Lock Shift Actuator 5.042,6.781 7.094,7.052 2.052,0.271 10 false Transfer Shift Actuator Assembly 5.563,2.844 6.021,3.042 0.458,0.198 10 false TM1 5.563,3.51 6.021,3.708 0.458,0.198 10 false TM2 4.333,2.833 4.792,3.031 0.458,0.198 10 false TM1 4.344,3.49 4.802,3.688 0.458,0.198 10 false TM2 5.167,2.969 5.625,3.167 0.458,0.198 10 false C47 5.188,3.635 5.646,3.833 0.458,0.198 10 false C47 5.271,2.75 5.427,2.948 0.156,0.198 10 false 1 5.229,3.406 5.385,3.604 0.156,0.198 10 false 2 1.417,6.677 3.281,6.896 1.865,0.219 10 false 4 Wheel Drive Control ECU 4.813,2.719 4.969,2.917 0.156,0.198 10 false 1 4.823,3.417 4.979,3.615 0.156,0.198 10 false 2 1.271,0.646 2.375,1.125 1.104,0.479 10 false Current Detection Circuit 1.49,2.75 2.365,2.917 0.875,0.167 10 false Drive Circuit 1.49,5.156 2.417,5.344 0.927,0.188 10 false Drive Circuit 1.479,3.927 2.385,4.135 0.906,0.208 10 false Drive Circuit 0.49,2.781 0.948,2.979 0.458,0.198 10 false CPU 1.573,1.938 1.729,2.135 0.156,0.198 10 false * 0.333,7.281 2.813,7.479 2.479,0.198 10 false *: Motor Drive Circuit Monitor Voltage 3.344,0.396 3.802,0.594 0.458,0.198 10 false IGR 3.25,2.542 3.406,2.74 0.156,0.198 10 false 1 3.594,3.177 3.781,3.385 0.188,0.208 10 false 2 2.854,3.844 3.01,4.042 0.156,0.198 10 false 3 3.25,4.458 3.406,4.656 0.156,0.198 10 false 4 2.49,5 2.646,5.198 0.156,0.198 10 false 5 2.823,5.688 2.979,5.885 0.156,0.198 10 false 6

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - 4 WHEEL DRIVE CONTROL ECU)
a.

Disconnect the B11 4 wheel drive control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B11)Location & Routing

Click Connector(B11)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

B11-6 (HM1) - Body ground Ignition switch off Below 1.5 V
B11-6 (HM1) - Body ground Ignition switch ON Below 1.5 V
B11-7 (HM2) - Body ground Ignition switch off Below 1.5 V
B11-7 (HM2) - Body ground Ignition switch ON Below 1.5 V
B11-1 (TM1) - Body ground Ignition switch off Below 1.5 V
B11-1 (TM1) - Body ground Ignition switch ON Below 1.5 V
B11-2 (TM2) - Body ground Ignition switch off Below 1.5 V
B11-2 (TM2) - Body ground Ignition switch ON Below 1.5 V



c.

Connect the B11 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.

Disconnect the B11 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B11)Location & Routing

Click Connector(B11)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

B11-6 (HM1) - Body ground Always 10 kΩ or higher
B11-7 (HM2) - Body ground Always 10 kΩ or higher
B11-1 (TM1) - Body ground Always 10 kΩ or higher
B11-2 (TM2) - Body ground Always 10 kΩ or higher



c.

Connect the B11 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.

Disconnect the B11 4 wheel drive control ECU connector.


b.

Disconnect the C48 high-low shift motor (transfer shift actuator assembly) connector.


c.

Disconnect the C47 center differential lock shift actuator (transfer shift actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B11)Location & Routing

Click Connector(B11)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

B11-6 (HM1) - Body ground Always 10 kΩ or higher
B11-7 (HM2) - Body ground Always 10 kΩ or higher
B11-1 (TM1) - Body ground Always 10 kΩ or higher
B11-2 (TM2) - Body ground Always 10 kΩ or higher



e.

Connect the C47 center differential lock shift actuator (transfer shift actuator assembly) connector.


f.

Connect the C48 high-low shift motor (transfer shift actuator assembly) connector.


g.

Connect the B11 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR