Home › Engine / Hybrid System › V35A-FTS (FUEL) › FUEL INJECTOR (for Port Injection)
RM38G0E _51 Engine / Hybrid System _101368 V35A-FTS FUEL _0470021 FUEL INJECTOR(for Port Injection) G

V35A-FTS FUEL  FUEL INJECTOR(for Port Injection)  INSPECTION  


PROCEDURE

Hide 23250F 1.INSPECT PORT FUEL INJECTOR ASSEMBLY

a.

Check the resistance.

i.
A401655C10
0.75,0.042 1.083,0.229 0.333,0.188 2.115,0.042 2.448,0.229 0.333,0.188 0.75,0.292 1.115,0.479 0.365,0.188 2.115,0.292 2.479,0.479 0.365,0.188 1.479,0.292 1.813,0.479 0.333,0.188 1.469,0.042 1.833,0.229 0.365,0.188 0.073,0.052 0.292,0.24 0.219,0.188 10 false *a 0.833,0.052 1.083,0.229 0.25,0.177 10 false F1 1.531,0.052 1.865,0.229 0.333,0.177 10 false G1 2.198,0.052 2.448,0.229 0.25,0.177 10 false F2 0.813,0.302 1.146,0.479 0.333,0.177 10 false G2 1.552,0.313 1.854,0.479 0.302,0.167 10 false F3 2.188,0.302 2.521,0.479 0.333,0.177 10 false G3
*a Component without harness connected
(Port Fuel Injector Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F1,G1,F2,G2,F3,G3)Location & Routing

Click Connector(F1)Engine Compartment>No. 7 Engine Wire>No. 1 Fuel Injector Assembly (for Port Injection)

Click Connector(G1)Engine Compartment>No. 8 Engine Wire>No. 2 Fuel Injector Assembly (for Port Injection)

Click Connector(F2)Engine Compartment>No. 7 Engine Wire>No. 3 Fuel Injector Assembly (for Port Injection)

Click Connector(G2)Engine Compartment>No. 8 Engine Wire>No. 4 Fuel Injector Assembly (for Port Injection)

Click Connector(F3)Engine Compartment>No. 7 Engine Wire>No. 5 Fuel Injector Assembly (for Port Injection)

Click Connector(G3)Engine Compartment>No. 8 Engine Wire>No. 6 Fuel Injector Assembly (for Port Injection)

F1-1 - F1-2 20°C (68°F) 11.6 to 12.4 Ω
G1-1 - G1-2 20°C (68°F) 11.6 to 12.4 Ω
F2-1 - F2-2 20°C (68°F) 11.6 to 12.4 Ω
G2-1 - G2-2 20°C (68°F) 11.6 to 12.4 Ω
F3-1 - F3-2 20°C (68°F) 11.6 to 12.4 Ω
G3-1 - G3-2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the port fuel injector assembly.



b.

Check the operation.

CAUTION:

Perform the inspection in a well-ventilated area.

Do not perform the inspection near an open flame.


i.

Discharge fuel system pressure.

Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>PRECAUTION


ii.
A487616

Disconnect the fuel tube sub-assembly.

Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>PRECAUTION


iii.
A264971C19
0.5,1.656 0.729,1.885 0.729,1.885 0.833,1.885 false 0.854,0.906 1.146,0.615 1.146,0.615 1.26,0.615 false 1.99,1.292 2.292,1.594 2.292,1.594 2.417,1.594 false 2.646,0.698 2.948,0.396 2.948,0.396 3.063,0.396 false 0.875,1.802 1.156,2.042 0.281,0.24 10 false *a 1.333,0.521 1.656,0.781 0.323,0.26 10 false *b 2.479,1.51 2.802,1.76 0.323,0.25 10 false *c 3.135,0.292 3.354,0.542 0.219,0.25 10 false *d
*a SST (Hose)
*b SST (Hose Band)
*c SST (Fuel Tube Connector)
*d Fuel Pipe (Vehicle Side)


Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).

SST
09268-31015  (09268-41500, 09268-41700, 95336-08070)

NOTICE:

Make sure the SST (fuel tube connector) O-rings are not damaged and are free of foreign matter as they are used to seal the connections between the fuel tube connector and fuel pipe.



iv.

Apply a light coat of gasoline to a new fuel injector O-ring, and install the fuel injector O-ring to the port fuel injector assembly.


v.
A333797C03
1.281,0.135 1.563,0.135 false 1.906,0.292 2.188,0.292 false 1.26,0.813 1.542,0.813 false 2.563,1.146 2.844,1.146 false 1.135,1.24 1.573,1.24 false 1.281,2.052 1.563,2.052 false 0.958,1.167 1.271,1.323 0.313,0.156 10 false *1 1.083,0.729 1.396,0.885 0.313,0.156 10 false *a 2.25,0.219 2.563,0.375 0.313,0.156 10 false *b 2.896,1.063 3.208,1.219 0.313,0.156 10 false *c 1.115,0.063 1.427,0.219 0.313,0.156 10 false *d 1.104,1.969 1.417,2.125 0.313,0.156 10 false *e
*1 Fuel Injector O-Ring
*a SST (Adapter)
*b SST (Hose Band)
*c SST (Clamp)
*d SST (Hose)
*e Vinyl Tube


Connect SST (adapter) and SST (hose) to the port fuel injector assembly, and hold the port fuel injector assembly and union with SST (adapter).

SST
09268-31015  (09268-41410, 09268-41600, 09268-41700, 95336-08070)


vi.

Install a vinyl tube to the port fuel injector assembly.

CAUTION:

Install a suitable vinyl tube to the port fuel injector assembly to prevent fuel from spraying.



vii.
A333798C01
1.427,1.615 1.667,2.052 1.667,2.052 1.813,2.052 false 1.583,1.323 2.198,1.75 2.198,1.75 2.417,1.75 true 2.469,1.656 2.781,1.813 0.313,0.156 10 false *a 1.865,1.969 2.188,2.167 0.323,0.198 10 false *b
*a Lock
*b SST (Tie Band)


Tie SST (clamp) and SST (adapter) together with SST (tie band) as shown in the illustration.

SST
09268-31015  (09268-41800)

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

·

Before using SST (tie band), make sure that there is no wear, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



viii.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


ix.

Set the port fuel injector assembly into a graduated cylinder.

NOTICE:

Do not start the engine.



x.
A333799C01
2.073,0.885 2.073,0.427 false 2,0.917 2.313,1.073 0.313,0.156 10 false *a
*a SST (EFI Inspection Wire K)


Connect SST (EFI inspection wire K) to the port fuel injector assembly and battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each port fuel injector assembly 2 or 3 times.

SST
09842-30110  

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay (Brushless)
50004 372 40
Standard Injection Volume:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - Negative (-) battery terminal Per 15 seconds 67 to 82 cc (4.1 to 5.0 cu.in.)


Difference between Each Port Fuel Injector Assembly:

15 cc (0.9 cu.in.) or less


NOTICE:
·

Make sure that SST (EFI inspection wire K) is securely connected.

·

Always switch the voltage on and off at the battery side, not the port fuel injector assembly side.



If the injection volume is not as specified, replace the port fuel injector assembly.



c.

Check for leaks.

i.

Disconnect SST (EFI inspection wire K) from the battery and port fuel injector assembly. and check for fuel leaks from the port fuel injector assembly.

Standard Fuel Drop:

1 drop or less per 20 minutes


If the result is not as specified, replace the port fuel injector assembly.


ii.

Connect the fuel tube sub-assembly.

Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>PRECAUTION