Home › Engine / Hybrid System › V35A-FTS (FUEL) › FUEL PUMP ECU
RM38G0E _51 Engine / Hybrid System _101368 V35A-FTS FUEL _0470029 FUEL PUMP ECU A

V35A-FTS FUEL  FUEL PUMP ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A482106N01
1.438,2.042 1.729,2.042 1.729,2.042 2.229,2.271 false 6.302,0.26 6.844,0.26 false 6.333,0.688 6.823,0.688 false 1.854,1.229 2.135,1.229 2.135,1.229 3.177,1.854 false 6.125,0.094 6.385,0.365 0.26,0.271 18 false 1 6.156,0.531 6.417,0.802 0.26,0.271 18 false 2 1.615,1.104 1.875,1.375 0.26,0.271 18 false 3 1.229,1.885 1.49,2.156 0.26,0.271 18 false 4 1.813,2.521 2.063,2.698 0.25,0.177 10 false x 2 2.031,3.052 2.292,3.219 0.26,0.167 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 FUEL PUMP CONTROL ECU 89571 (Click here) - -
4 FUEL PUMP CONTROL ECU BRACKET 89573 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump control ECU removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 89571 3.REMOVE FUEL PUMP CONTROL ECU

Z101186

NOTICE:

Make sure the fuel pump control ECU is not subjected to physical shocks, such as being dropped, etc.



a.
A482104


Hide 89573 4.REMOVE FUEL PUMP CONTROL ECU BRACKET

a.
A482105