Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL PRESSURE PULSATION DAMPER
RM38G0E _51 Engine / Hybrid System _101386 1GR-FE FUEL _0470054 FUEL PRESSURE PULSATION DAMPER A

1GR-FE FUEL  FUEL PRESSURE PULSATION DAMPER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A482120N01
6.281,0.25 6.865,0.25 false 6.292,0.677 6.844,0.677 false 5.99,2.333 5.823,2.333 5.823,2.333 5.323,1.833 false 1.396,1.135 2.313,1.135 false 5.635,1.75 6.219,1.75 false 5.813,0.094 6.313,0.365 0.5,0.271 18 false 1, 2 6.115,0.542 6.385,0.813 0.271,0.271 18 false 3 1.219,0.99 1.49,1.26 0.271,0.271 18 false 4 6.271,1.594 6.542,1.865 0.271,0.271 18 false 5 6.031,2.167 6.469,2.438 0.438,0.271 18 false ● 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 DISCHARGE FUEL SYSTEM PRESSURE - (Click here) - -
2 PRECAUTION - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
4 INTAKE AIR SURGE TANK 17129 - - -
5 FUEL PRESSURE PULSATION DAMPER ASSEMBLY 23270 - - -
6 PULSATION DAMPER O-RING 23270F - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during port fuel pressure pulsation damper removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 17129 4.REMOVE INTAKE AIR SURGE TANK

Hide 23270 5.REMOVE FUEL PRESSURE PULSATION DAMPER ASSEMBLY

a.
A482118


Hide 23270F 6.REMOVE PULSATION DAMPER O-RING

a.
A487594