Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P010012  Mass or Volume Air Flow Sensor "A" Circuit Short to Battery  P010014  Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open  P010A12  Mass or Volume Air Flow Sensor "B" Circuit Short to Battery  P010A14  Mass or Volume Air Flow Sensor "B" Circuit Short to Ground or Open  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the intake air volume using the following built-in components:

·

By-pass duct (allows some of the intake air to flow past a silicon chip sensor)

·

Silicon chip sensor (uses a heater control bridge circuit and temperature sensor bridge circuit to detect the difference in the temperature of the intake air that passes the sensors positioned before and after the heater)

·

Control circuit (converts the difference in temperature into a pulse signal and performs correction)


Intake air flows past the temperature sensor (before heater), the heater, and then the temperature sensor (after heater) of the silicon chip sensor in the by-pass duct. As the intake air is warmed up when it is exposed to the heater, the temperature of the intake air as it flows past the temperature sensor (after heater) is higher than when it flows past the temperature sensor (before heater). The difference in temperature of the intake air at each temperature sensor varies depending on the velocity of the intake air that flows past the silicon chip sensor. The temperature sensor bridge circuit detects the difference in temperature and the control circuit converts it into a pulse signal and outputs it to the ECM. When the temperature detected by the temperature sensor (before heater) is higher than that detected by the temperature sensor (after heater), backflow of the intake air is detected.

The ECM calculates the intake air volume based on the pulse signal received from the mass air flow meter sub-assembly, and uses it to determine the fuel injection duration necessary for an optimal air-fuel ratio.

The heater control bridge circuit has a temperature sensor and power transistor, and maintains the temperature differential between the heater temperature and intake air temperature at a specific level.

HINT:

When DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM calculates the fuel injection duration based on the engine speed and throttle valve angle. Fail-safe mode continues until a pass condition is detected.


A431660C01
5.073,1.719 4.917,0.917 4.917,0.917 4.75,0.917 true 5.073,2.521 5,3 5,3 4.833,3 true 0.667,3 0.833,3.5 0.833,3.5 1,3.5 true 6.5,2.333 6.333,2.333 6.333,2.333 6.26,2.063 true 0.417,0.333 0.667,0.5 0.25,0.167 10 false *1 6.427,1.49 6.677,1.646 0.25,0.156 10 false *a 3.125,1.49 3.375,1.656 0.25,0.167 10 false *b 4.635,2.917 4.885,3.073 0.25,0.156 10 false *c 4.531,0.844 4.781,1.01 0.25,0.167 10 false *d 3.646,1.854 3.958,2.01 0.313,0.156 10 false *e 1.063,3.427 1.375,3.583 0.313,0.156 10 false *f 6.583,2.25 6.833,2.406 0.25,0.156 10 false *f
*1 Mass Air Flow Meter Sub-assembly - -
*a Upstream Side *b Downstream Side
*c Heater *d Temperature Distribution Without Airflow
*e Flow Rate Detection by Temperature Differential *f Intake Air


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P010012 Mass or Volume Air Flow Sensor "A" Circuit Short to Battery The mass air flow meter sub-assembly (bank 1) output frequency is higher than 9.8 kHz for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly (bank 1) circuit

·

Mass air flow meter sub-assembly (bank 1)

·

ECM


Comes on SAE: P0103
P010014 Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open The mass air flow meter sub-assembly (bank 1) output frequency is less than 0.1 kHz for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly (bank 1) circuit

·

Mass air flow meter sub-assembly (bank 1)

·

ECM


Comes on SAE: P0102
P010A12 Mass or Volume Air Flow Sensor "B" Circuit Short to Battery The mass air flow meter sub-assembly (bank 2) output frequency is higher than 9.8 kHz for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly (bank 2) circuit

·

Mass air flow meter sub-assembly (bank 2)

·

ECM


Comes on SAE: P010D
P010A14 Mass or Volume Air Flow Sensor "B" Circuit Short to Ground or Open The mass air flow meter sub-assembly (bank 2) output frequency is less than 0.1 kHz for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly (bank 2) circuit

·

Mass air flow meter sub-assembly (bank 2)

·

ECM


Comes on SAE: P010C

MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter sub-assembly, the frequency level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly circuit and stores a DTC.

Example:

When the sensor output frequency remains less than 0.1 kHz, or higher than 9.8 kHz for 3 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more [A].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P010012, P010014, P010A12 or P010A14.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [A] through [B] again.




WIRING DIAGRAM

A480728E01
0.333,2.958 3.177,3.24 2.844,0.281 10 false Mass Air Flow Meter Sub-assembly (Bank 1) 0.26,6.031 3.281,6.323 3.021,0.292 10 false Mass Air Flow Meter Sub-assembly (Bank 2) 0.333,2.781 0.729,3 0.396,0.219 10 false C24 0.26,5.875 0.656,6.094 0.396,0.219 10 false C25 1.573,0.823 1.99,1.042 0.417,0.219 10 false VCCR 1.635,1.531 1.969,1.74 0.333,0.208 10 false FGR 1.542,2.302 1.979,2.521 0.438,0.219 10 false E2GR 2.115,0.688 2.448,0.906 0.333,0.219 10 false 4 2.115,1.375 2.448,1.594 0.333,0.219 10 false 3 2.104,2.156 2.438,2.375 0.333,0.219 10 false 2 1.656,3.917 2.083,4.135 0.427,0.219 10 false VCC 1.74,4.625 2.073,4.844 0.333,0.219 10 false FG 1.656,5.396 2.083,5.615 0.427,0.219 10 false E2G 2.104,3.781 2.438,4 0.333,0.219 10 false 4 2.104,4.479 2.438,4.698 0.333,0.219 10 false 3 2.115,5.24 2.448,5.458 0.333,0.219 10 false 2 4.604,0.698 5.052,0.917 0.448,0.219 10 false VCVG 4.615,1.396 5.063,1.615 0.448,0.219 10 false VG 4.604,2.167 4.938,2.385 0.333,0.219 10 false E2G 5.24,1.219 5.688,1.438 0.448,0.219 10 false 2.2 kΩ 5.333,4.281 5.781,4.5 0.448,0.219 10 false 2.2 kΩ 4.625,4.479 5.073,4.698 0.448,0.219 10 false VG2 5.698,6.198 6.135,6.427 0.438,0.229 10 false ECM 4.281,0.688 4.615,0.906 0.333,0.219 10 false 84 4.281,1.385 4.615,1.604 0.333,0.219 10 false 78 4.281,2.167 4.615,2.385 0.333,0.219 10 false 83 4.281,4.469 4.615,4.688 0.333,0.219 10 false 76 6.208,0.5 6.656,0.719 0.448,0.219 10 false 5 V 5.688,6.021 6.125,6.25 0.438,0.229 10 false C37 4.615,5.24 5.094,5.458 0.479,0.219 10 false E2G2 4.25,5.24 4.583,5.458 0.333,0.219 10 false 81 4.635,3.76 5.083,3.979 0.448,0.219 10 false VVG2 4.281,3.771 4.615,3.99 0.333,0.219 10 false 82

CAUTION / NOTICE / HINT

HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P010012, P010014 Bank 1
P010A12, P010A14 Bank 2



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C24,C25)Location & Routing

Click Connector(C24)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly RH

Click Connector(C25)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly LH

C24-4 (VCCR) - C24-3 (FGR) Ignition switch off 2.09 to 2.31 kΩ
C25-4 (VCC) - C25-3 (FG) Ignition switch off 2.09 to 2.31 kΩ
C24-2 (E2GR) - Body ground Always Below 1 Ω
C25-2 (E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C24,C37,C25)Location & Routing

Click Connector(C24)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly RH

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C25)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly LH

C24-4 (VCCR) - C37-84 (VCVG) Always Below 1 Ω
C24-3 (FGR) - C37-78 (VG) Always Below 1 Ω
C24-2 (E2GR) - C37-83 (E2G) Always Below 1 Ω
C25-4 (VCC) - C37-82 (VVG2) Always Below 1 Ω
C25-3 (FG) - C37-76 (VG2) Always Below 1 Ω
C25-2 (E2G) - C37-81 (E2G2) Always Below 1 Ω
C24-4 (VCCR) or C37-84 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
C24-3 (FGR) or C37-78 (VG) - Body ground and other terminals Always 10 kΩ or higher
C25-4 (VCC) or C37-82 (VVG2) - Body ground and other terminals Always 10 kΩ or higher
C25-3 (FG) or C37-76 (VG2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR