Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P010511  Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Ground  


DESCRIPTION

A327839E06
0.073,0.052 0.844,0.25 0.771,0.198 10 false Voltage (V) 0.958,0.26 3.219,0.583 2.26,0.323 10 false Intake Manifold Absolute Pressure 0.24,0.74 1.01,0.938 0.771,0.198 10 false 4.5 0.25,1.563 1.021,1.76 0.771,0.198 10 false 2.0 0.25,2.01 1.021,2.208 0.771,0.198 10 false 1.0 3.021,2.375 3.396,2.802 0.375,0.427 10 false kPa 3,2.854 3.427,3.24 0.427,0.385 10 false psi 0.854,2.563 1.302,2.771 0.448,0.208 10 false 13.30 1.458,2.563 1.906,2.771 0.448,0.208 10 false 96.15 2.51,2.563 3.083,2.781 0.573,0.219 10 false 303.30 0.917,3.042 1.271,3.271 0.354,0.229 10 false 1.93 1.49,3.052 2.031,3.323 0.542,0.271 10 false 13.94 2.552,3.052 3.031,3.281 0.479,0.229 10 false 43.98

The No. 3 turbo pressure sensor detects the intake manifold pressure as a change in voltage. The ECM calculates the intake manifold pressure based on this voltage.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P010511 Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Ground The No. 3 turbo pressure sensor output voltage is less than 0.9 V for 3 seconds or more (1 trip detection logic).
·

Open or short in No. 3 turbo pressure sensor circuit

·

No. 3 turbo pressure sensor

·

ECM


Comes on SAE: P0107

HINT:

When a DTC is output, check the Data List item "Intake Manifold Absolute Pressure" using the GTS.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

DTC No. Intake Manifold Absolute Pressure Malfunction
P010511 Approximately 0 kPa (0 psi)
·

Short to ground in PIM circuit

·

Short in PIM to EPIM circuit

·

Open in VCPM circuit



If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM monitors the No. 3 turbo pressure sensor voltage and uses this value to calculate the intake manifold pressure. When the No. 3 turbo pressure sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the No. 3 turbo pressure sensor circuit, illuminates the MIL and stores a DTC.

Example:

If the sensor output voltage is less than 0.9 V for 3 seconds or more, the ECM stores this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine and wait 5 seconds or more.

7.

Turn the GTS on.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P010511.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

A377141E58
0.333,2.771 0.646,2.969 0.313,0.198 10 false C40 0.333,2.969 2.823,3.25 2.49,0.281 10 false No. 3 Turbo Pressure Sensor 1.469,0.906 1.906,1.198 0.438,0.292 10 false VC 1.406,1.583 1.844,1.875 0.438,0.292 10 false PIM 1.479,2.385 1.917,2.677 0.438,0.292 10 false E2 1.781,0.813 2.219,1.104 0.438,0.292 10 false 3 1.792,1.5 2.229,1.792 0.438,0.292 10 false 1 1.781,2.271 2.219,2.563 0.438,0.292 10 false 2 4.396,0.792 4.833,1.083 0.438,0.292 10 false 40 4.677,0.792 5.427,1.115 0.75,0.323 10 false VCPM 4.396,1.49 4.833,1.781 0.438,0.292 10 false 38 4.677,1.49 5.427,1.813 0.75,0.323 10 false PIM 4.406,2.26 4.844,2.552 0.438,0.292 10 false 39 4.677,2.26 5.427,2.583 0.75,0.323 10 false EPIM 5.26,3 5.698,3.292 0.438,0.292 10 false C38 5.271,3.167 5.708,3.458 0.438,0.292 10 false ECM 5.646,0.583 6.083,0.875 0.438,0.292 10 false 5 V 5.313,1.302 6.063,1.625 0.75,0.323 10 false 180 kΩ

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the No. 3 turbo pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C40)Location & Routing

Click Connector(C40)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>E.F.I. Vacuum Sensor Assembly

C40-3 (VC) - C40-2 (E2) Ignition switch ON 4.75 to 5.25 V
C40-1 (PIM) - C40-2 (E2) Ignition switch ON 1.2 to 5.25 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C40)Location & Routing

Click Connector(C40)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>E.F.I. Vacuum Sensor Assembly

C40-3 (VC) - C40-1 (PIM) Ignition switch off 171 to 189 kΩ



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (NO. 3 TURBO PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (NO. 3 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the No. 3 turbo pressure sensor connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR