The intake air temperature sensor, mounted on the mass air flow meter sub-assembly, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes.
The intake air temperature detected by the inlet air temperature sensor is converted to a voltage value inside the intake airflow meter assembly, and the voltage value is then output to the ECM. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.
When DTC P00AA11 or P011011 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P00AA11 | Intake Air Temperature Sensor 1 Bank 2 Circuit Short to Ground | The intake air temperature sensor (bank 2) output voltage is less than 0.663 V for 0.5 seconds or more (1 trip detection logic). |
·
Short in intake air temperature sensor (bank 2)
·
Intake air temperature sensor (bank 2) (mass air flow meter sub-assembly)
·
ECM |
Comes on | SAE: P00AC |
| P011011 | Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground | The intake air temperature sensor (bank 1) output voltage is less than 0.663 V for 0.5 seconds or more (1 trip detection logic). |
·
Short in intake air temperature sensor (bank 1) circuit
·
Intake air temperature sensor (bank 1) (mass air flow meter sub-assembly)
·
ECM |
Comes on | SAE: P0112 |
When a DTC is output, check the Data List item "Intake Air Temperature B1S1 and Intake Air Temperature B2S1" using the GTS.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
| DTC No. | Intake Air Temperature B1S1 or Intake Air Temperature B2S1 | Malfunction |
|---|---|---|
| P00AA11 | -39°C (-38.2°F) or less |
·
Short to ground in THA2 circuit
·
Short in THA2 to E2G2 circuit
·
Open in VVG2 circuit |
| P011011 |
·
Short to ground in THA circuit
·
Short in THA to E2G circuit
·
Open in VCVG circuit |
If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor (mass air flow meter sub-assembly) circuit, illuminates the MIL and stores a DTC.
Example:
If the intake air temperature sensor output voltage is less than 0.663 V for 0.5 seconds or more, the ECM will illuminate the MIL and store this DTC.
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Wait 0.5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P00AA11 or P011011.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
| DTC | Suspected Area |
|---|---|
| P011011 | Bank 1 |
| P00AA11 | Bank 2 |
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Disconnect the mass air flow meter sub-assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C24,C25)Location & Routingewd_type=routing;type=c,c;code=C24,C25 |
||
| C24-4 (VCCR) - C24-2 (E2GR) | Ignition switch ON | 4.8 to 5.2 V |
| C24-1 (THAR) - C24-2 (E2GR) | Ignition switch ON | 4.8 to 5.2 V |
| C25-4 (VCC) - C25-2 (E2G) | Ignition switch ON | 4.8 to 5.2 V |
| C25-1 (THA) - C25-2 (E2G) | Ignition switch ON | 4.8 to 5.2 V |
Turn the ignition switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C24,C25)Location & Routingewd_type=routing;type=c,c;code=C24,C25 |
||
| C24-4 (VCCR) - C24-1 (THAR) | Ignition switch off | 2.565 to 2.835 kΩ |
| C25-4 (VCC) - C25-1 (THA) | Ignition switch off | 2.565 to 2.835 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C24,C37,C25)Location & Routingewd_type=routing;type=c,c,c;code=C24,C37,C25 |
||
| C24-4 (VCCR) - C37-84 (VCVG) | Always | Below 1 Ω |
| C25-4 (VCC) - C37-82 (VVG2) | Always | Below 1 Ω |
| C24-1 (THAR) or C37-77 (THA) - Body ground and other terminals | Always | 10 kΩ or higher |
| C25-1 (THA) or C37-75 (THA2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG