Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P011515  Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P011511.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P011511

HINT:

When DTC P011515 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P011515 Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open The engine coolant temperature sensor output voltage is higher than 3.76 V for 0.5 seconds or more (1 trip detection logic).
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on SAE: P0118

HINT:

When a DTC is output, check the Data List item "Coolant Temperature" using the GTS.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

DTC No. Coolant Temperature Malfunction
P011515 -40°C (-40°F)
·

Short to +B in THW circuit

·

Open in THW circuit

·

Open in ETHW circuit



If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The engine coolant temperature sensor is used to monitor the engine coolant temperature. The engine coolant temperature sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the engine coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance decreases. These variations in resistance are reflected in the output voltage from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the engine coolant temperature. If the engine coolant temperature sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the engine coolant temperature sensor circuit, illuminates the MIL and stores a DTC.

Example:

If the engine coolant temperature sensor output voltage is higher than 3.76 V for 0.5 seconds or more, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P011515.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the engine coolant temperature sensor connector.

A402987C36
4.427,1.271 4.844,1.51 0.417,0.24 4.719,2.229 5.375,1.573 true 6.271,2.281 5.708,1.573 true 0.792,0.438 1.115,0.74 0.323,0.302 10 false *1 3.094,0.458 3.417,0.76 0.323,0.302 10 false *2 4.802,0.479 5.125,0.781 0.323,0.302 10 false *a 2.917,1.26 3.396,1.563 0.479,0.302 10 false THW 2.917,1.771 3.531,2.125 0.615,0.354 10 false ETHW 4.51,1.313 5.125,1.667 0.615,0.354 10 false C28 1.333,1.021 1.781,1.323 0.448,0.302 10 false THW 1.323,1.406 1.646,1.708 0.323,0.302 10 false E2 4.604,2.26 4.927,2.563 0.323,0.302 10 false E2 6.208,2.323 6.688,2.573 0.479,0.25 10 false THW
*1 Engine Coolant Temperature Sensor *2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)
- -



b.

Connect terminals 1 (E2) and 2 (THW) of the engine coolant temperature sensor connector on the wire harness side.


c.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
OK:
GTS Display Specified Condition
Coolant Temperature Higher than 135°C (275°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR