Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P210018  Throttle Actuator "A" Control Motor Circuit Current Below Threshold  P210019  Throttle Actuator "A" Control Motor Circuit Current Above Threshold  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.

The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body with motor assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P210018 Throttle Actuator "A" Control Motor Circuit Current Below Threshold Both of the following conditions are met for 2 seconds or more (1 trip detection logic):
·

The throttle actuator drive duty cycle is 80% or higher.

·

The throttle actuator current is less than 0.5 A.


·

Open or short in throttle actuator circuit

·

Throttle actuator

·

ECM


Comes on SAE: P2102
P210019 Throttle Actuator "A" Control Motor Circuit Current Above Threshold Either of the following conditions is met (1 trip detection logic):
·

A motor driver IC high current limiter monitor input malfunction is detected.

·

A motor driver IC high current inhibit signal is received.


·

Open or short in throttle actuator circuit

·

Throttle actuator

·

Throttle valve

·

Throttle body with motor assembly

·

ECM


Comes on SAE: P2103

MONITOR DESCRIPTION

The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not operate properly (for example, it is stuck open), the ECM will determine there is a malfunction, illuminate the MIL and store a DTC.

MONITOR STRATEGY

Required Sensors/Components Throttle actuator (throttle body with motor assembly)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A220567E46
3.656,1.448 3.229,0.396 3.229,0.396 3.51,0.396 false 4.802,1.979 5.24,1.083 5.24,1.083 5.396,1.083 false 2.667,1.99 2.438,1.156 2.438,1.156 2.604,1.156 false 1.24,1.823 1.635,2.042 0.396,0.219 10 false Idling 0.438,2.146 1.969,2.5 1.531,0.354 10 false Ignition Switch ON 2.115,2.031 2.406,2.24 0.292,0.208 10 false [A] 3.844,1.75 4.083,1.938 0.24,0.188 10 false [B] 5.479,0.99 6.146,1.156 0.667,0.167 10 false Released 3.583,0.302 4.385,0.469 0.802,0.167 10 false Depressed 3.521,2.729 4.719,2.917 1.198,0.188 10 false 2 seconds or more 5.271,3.521 5.531,3.729 0.26,0.208 10 false [C] 3.802,3.167 5.417,3.354 1.615,0.188 10 false 16 seconds or more 2.656,1.073 3.333,1.25 0.677,0.177 10 false Released

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Start the engine.

9.

With the vehicle stationary, fully depress the accelerator pedal and quickly release it [B].

10.

Check that 16 seconds or more have elapsed since the accelerator pedal was first depressed.

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P210018 or P210019.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




FAIL-SAFE

When these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 8.5° throttle valve opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM

A485557E01
1.073,4.365 1.688,4.563 0.615,0.198 10 false Battery 3.406,1.25 3.813,1.49 0.406,0.24 10 false ETCS 1.76,3.563 3.427,3.969 1.667,0.406 10 false Throttle Actuator (Built into Throttle Body Assembly) 1.76,3.385 2.073,3.573 0.313,0.188 10 false C20 2.688,2.052 2.99,2.365 0.302,0.313 10 false M+ 2.708,2.854 2.979,3.104 0.271,0.25 10 false M- 3.01,2.042 3.219,2.292 0.208,0.25 10 false 6 3.031,2.865 3.24,3.115 0.208,0.25 10 false 5 5.344,2.104 6.396,2.75 1.052,0.646 10 false Throttle Actuator Control Circuit 4.49,1.094 4.865,1.354 0.375,0.26 10 false C38 4.5,2.156 4.865,2.385 0.365,0.229 10 false C37 4.49,3 4.885,3.26 0.396,0.26 10 false C37 4.521,4.198 4.771,4.458 0.25,0.26 10 false B1 4.563,0.865 4.781,1.021 0.219,0.156 10 false 1 4.563,1.938 4.823,2.104 0.26,0.167 10 false 3 4.563,2.792 4.823,2.958 0.26,0.167 10 false 4 4.563,3.969 4.823,4.135 0.26,0.167 10 false 9 4.854,0.979 5.229,1.167 0.375,0.188 10 false +BM 4.854,2.052 5.229,2.24 0.375,0.188 10 false M+ 4.865,2.885 5.24,3.073 0.375,0.188 10 false M- 4.865,4.094 5.24,4.281 0.375,0.188 10 false E1 5.656,5.01 6.302,5.323 0.646,0.313 10 false ECM 1.042,1.26 2.156,1.49 1.115,0.229 10 false SUB R/B-NO. 1

CAUTION / NOTICE / HINT

HINT:
·

The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Duty Ratio (Open) and Throttle Motor Duty Ratio (Close)) can be read using the GTS. However, the ECM shuts off the throttle actuator current when the electronic throttle control system malfunctions.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>THROTTLE BODY>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE WITH THROTTLE POSITION SENSOR BODY ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C20,C37)Location & Routing

Click Connector(C20)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Throttle with Throttle Position Sensor Body Assembly

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C20-6 (M+) - C37-3 (M+) Always Below 1 Ω
C20-5 (M-) - C37-4 (M-) Always Below 1 Ω
C20-6 (M+) or C37-3 (M+) - Body ground and other terminals Always 10 kΩ or higher
C20-5 (M-) or C37-4 (M-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for foreign matter between the throttle valve and the housing.

OK:

No foreign matter between the throttle valve and housing.


HINT:

Perform "Inspection After Repair" after cleaning the throttle body with motor assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE)

NG

REMOVE FOREIGN MATTER AND CLEAN THROTTLE BODY WITH MOTOR ASSEMBLY

4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE)
a.

Check if the throttle valve opens and closes smoothly.

OK:

Throttle valve opens and closes smoothly.


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE WITH THROTTLE POSITION SENSOR BODY ASSEMBLY)