Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P034011  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground  P034015  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open  P034511  Camshaft Position Sensor "A" Bank 2 Circuit Short to Ground  P034515  Camshaft Position Sensor "A" Bank 2 Circuit Short to Battery or Open  


DESCRIPTION

The camshaft position sensor (for intake camshaft) (VV1, VV2 signal) consists of a magnet and MRE (Magneto-Resistive Element).

The intake camshaft has a timing rotor for the camshaft position sensor. When the intake camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals. The ECM uses the pulse signals to determine the camshaft angle. Then the ECM uses this data to control fuel injection duration and injection timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P034011 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground The camshaft position sensor (for intake camshaft of bank 1) output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in camshaft position sensor (for intake camshaft of bank 1) circuit

·

Camshaft position sensor (for intake camshaft of bank 1)

·

ECM


Comes on SAE: P0342
P034015 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open The camshaft position sensor (for intake camshaft of bank 1) output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in camshaft position sensor (for intake camshaft of bank 1) circuit

·

Camshaft position sensor (for intake camshaft of bank 1)

·

ECM


Comes on SAE: P0343
P034511 Camshaft Position Sensor "A" Bank 2 Circuit Short to Ground The camshaft position sensor (for intake camshaft of bank 2) output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in camshaft position sensor (for intake camshaft of bank 2) circuit

·

Camshaft position sensor (for intake camshaft of bank 2)

·

ECM


Comes on SAE: P0347
P034515 Camshaft Position Sensor "A" Bank 2 Circuit Short to Battery or Open The camshaft position sensor (for intake camshaft of bank 2) output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in camshaft position sensor (for intake camshaft of bank 2) circuit

·

Camshaft position sensor (for intake camshaft of bank 2)

·

ECM


Comes on SAE: P0348

A356008E11
0.094,1.365 0.438,1.573 0.344,0.208 10 false CH1 0.115,2.094 0.458,2.302 0.344,0.208 10 false CH2 2.802,1.469 3.26,1.667 0.458,0.198 10 false GND 2.802,2.208 3.26,2.406 0.458,0.198 10 false GND

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.

·

VV1 stands for the camshaft position sensor signal (for intake camshaft of bank 1), and VV2 stands for the camshaft position sensor signal (for intake camshaft of bank 2).



ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between VV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


MONITOR DESCRIPTION

If the output voltage transmitted by the camshaft position sensor (for intake camshaft) remains low or high, the ECM interprets this as a malfunction in the sensor circuit, illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 10 seconds or more.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P034011, P034015, P034511 or P034515.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

A480731E01
0.521,2.083 0.979,2.281 0.458,0.198 10 false C11 0.521,2.25 2.417,2.615 1.896,0.365 10 false Camshaft Position Sensor (for Intake Camshaft of bank 1) 0.552,4.781 1.01,4.979 0.458,0.198 10 false C12 0.542,4.958 2.417,5.354 1.875,0.396 10 false Camshaft Position Sensor (for Intake Camshaft of bank 2) 4.552,0.469 4.771,0.698 0.219,0.229 10 false 70 4.552,1 4.844,1.229 0.292,0.229 10 false 89 4.542,1.552 4.781,1.781 0.24,0.229 10 false 69 2.073,0.479 2.292,0.708 0.219,0.229 10 false 3 2.063,1 2.281,1.229 0.219,0.229 10 false 1 2.073,1.552 2.292,1.781 0.219,0.229 10 false 2 4.865,3.125 5.406,3.375 0.542,0.25 10 false VCV2 1.688,0.479 1.906,0.708 0.219,0.229 10 false VC 1.531,1 1.958,1.208 0.427,0.208 10 false VVR+ 4.854,1.01 5.281,1.219 0.427,0.208 10 false VV1+ 1.563,1.563 2.094,1.76 0.531,0.198 10 false VVR- 4.865,4.219 5.292,4.427 0.427,0.208 10 false VV2- 1.542,3.708 1.969,3.917 0.427,0.208 10 false VVL+ 1.677,3.167 1.896,3.396 0.219,0.229 10 false VC 1.552,4.25 1.979,4.458 0.427,0.208 10 false VVL- 4.563,3.688 4.802,3.917 0.24,0.229 10 false 88 2.073,3.135 2.292,3.365 0.219,0.229 10 false 3 2.063,3.677 2.281,3.906 0.219,0.229 10 false 1 2.073,4.208 2.292,4.438 0.219,0.229 10 false 2 5.635,4.99 5.927,5.219 0.292,0.229 10 false C37 5.646,5.177 6.063,5.406 0.417,0.229 10 false ECM 4.854,1.563 5.281,1.771 0.427,0.208 10 false VV1- 5.781,3.552 6.375,3.781 0.594,0.229 10 false 1.5 kΩ 6.042,0.896 6.583,1.115 0.542,0.219 10 false 1.5 kΩ 4.865,3.677 5.292,3.885 0.427,0.208 10 false VV2+ 4.844,0.469 5.385,0.719 0.542,0.25 10 false VCV1 4.552,3.115 4.792,3.344 0.24,0.229 10 false 68 4.552,4.208 4.792,4.438 0.24,0.229 10 false 67

CAUTION / NOTICE / HINT

HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P034011, P034015 Bank 1
P034511, P034515 Bank 2



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.



d.

Turn the ignition switch off and wait for at least 30 seconds.



Result:
Proceed to
OK
NG



OK

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

NG

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C11,C37,C12)Location & Routing

Click Connector(C11)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor (Bank 1 Intake Side)

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C12)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor (Bank 2 Intake Side)

C11-1 (VVR+) - C37-89 (VV1+) Always Below 1 Ω
C11-2 (VVR-) - C37-69 (VV1-) Always Below 1 Ω
C11-3 (VC) - C37-70 (VCV1) Always Below 1 Ω
C12-1 (VVL+) - C37-88 (VV2+) Always Below 1 Ω
C12-2 (VVL-) - C37-67 (VV2-) Always Below 1 Ω
C12-3 (VC) - C37-68 (VCV2) Always Below 1 Ω
C11-1 (VVR+) or C37-89 (VV1+) - Body ground and other terminals Always 10 kΩ or higher
C11-2 (VVR-) or C37-69 (VV1-) - Body ground and other terminals Always 10 kΩ or higher
C11-3 (VC) or C37-70 (VCV1) - Body ground and other terminals Always 10 kΩ or higher
C12-1 (VVL+) or C37-88 (VV2+) - Body ground and other terminals Always 10 kΩ or higher
C12-2 (VVL-) or C37-67 (VV2-) - Body ground and other terminals Always 10 kΩ or higher
C12-3 (VC) or C37-68 (VCV2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR