Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P22AB11  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Short to Ground  P22AB12  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Short to Battery  P22AB13  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Open  P22AB16  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Voltage Below Threshold  P22AB17  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Voltage Above Threshold  P22B211  A/F (O2) Sensor Negative Current Control Bank 1 Sensor 2 Circuit Short to Ground  P22B212  A/F (O2) Sensor Negative Current Control Bank 1 Sensor 2 Circuit Short to Battery  P22B811  A/F (O2) Sensor Positive Current Control Bank 2 Sensor 2 Circuit Short to Ground  P22B812  A/F (O2) Sensor Positive Current Control Bank 2 Sensor 2 Circuit Short to Battery  P22B813  A/F (O2) Sensor Positive Current Control Bank 2 Sensor 2 Circuit Open  P22B816  A/F (O2) Sensor Positive Current Control Bank 2 Sensor 2 Circuit Voltage Below Threshold  P22B817  A/F (O2) Sensor Positive Current Control Bank 2 Sensor 2 Circuit Voltage Above Threshold  P22BF11  A/F (O2) Sensor Negative Current Control Bank 2 Sensor 2 Circuit Short to Ground  P22BF12  A/F (O2) Sensor Negative Current Control Bank 2 Sensor 2 Circuit Short to Battery  


DESCRIPTION

Refer to DTC P003612.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P003612

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P22AB11 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Short to Ground The A1B+ voltage is 1.43 V or less for 5 seconds or more (2 trip detection logic).
·

Short in air fuel ratio sensor (bank 1 sensor 2) circuit

·

Air fuel ratio sensor (bank 1 sensor 2)

·

ECM


Comes on SAE: P22AC
P22AB12 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Short to Battery The A1B+ voltage is higher than 6.135 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 2) circuit

·

Air fuel ratio sensor (bank 1 sensor 2)

·

ECM


Comes on SAE: P22AD
P22AB13 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Open 100 seconds or more elapse after the air fuel ratio sensor (bank 1 sensor 2) heater turns on and the air fuel ratio sensor (bank 1 sensor 2) impedance is higher than 510 Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 2) circuit

·

Air fuel ratio sensor (bank 1 sensor 2)

·

ECM


Comes on SAE: P22AB
P22AB16 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Voltage Below Threshold When A1B+ voltage is higher than 2.77 V, the difference between terminals A1B+ and A1B- is 0.2 V or less for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 2) circuit

·

Air fuel ratio sensor (bank 1 sensor 2)

·

ECM


Comes on SAE: P22AC
P22AB17 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Voltage Above Threshold Difference between terminals A1B+ and A1B- is higher than 1.72 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 2) circuit

·

Air fuel ratio sensor (bank 1 sensor 2)

·

ECM


Comes on SAE: P22AD
P22B211 A/F (O2) Sensor Negative Current Control Bank 1 Sensor 2 Circuit Short to Ground The A1B- voltage is 1.07 V or less for 5 seconds or more (2 trip detection logic).
·

Short in air fuel ratio sensor (bank 1 sensor 2) circuit

·

Air fuel ratio sensor (bank 1 sensor 2)

·

ECM


Comes on SAE: P22B3
P22B212 A/F (O2) Sensor Negative Current Control Bank 1 Sensor 2 Circuit Short to Battery The A1B- voltage is higher than 4.59 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 2) circuit

·

Air fuel ratio sensor (bank 1 sensor 2)

·

ECM


Comes on SAE: P22B4
P22B811 A/F (O2) Sensor Positive Current Control Bank 2 Sensor 2 Circuit Short to Ground The A2B+ voltage is 1.43 V or less for 5 seconds or more (2 trip detection logic).
·

Short in air fuel ratio sensor (bank 2 sensor 2) circuit

·

Air fuel ratio sensor (bank 2 sensor 2)

·

ECM


Comes on SAE: P22B9
P22B812 A/F (O2) Sensor Positive Current Control Bank 2 Sensor 2 Circuit Short to Battery The A2B+ voltage is higher than 6.135 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 2) circuit

·

Air fuel ratio sensor (bank 2 sensor 2)

·

ECM


Comes on SAE: P22BA
P22B813 A/F (O2) Sensor Positive Current Control Bank 2 Sensor 2 Circuit Open 100 seconds or more elapse after the air fuel ratio sensor (bank 2 sensor 2) heater turns on and the air fuel ratio sensor (bank 2 sensor 2) impedance is higher than 510 Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 2) circuit

·

Air fuel ratio sensor (bank 2 sensor 2)

·

ECM


Comes on SAE: P22B8
P22B816 A/F (O2) Sensor Positive Current Control Bank 2 Sensor 2 Circuit Voltage Below Threshold When A2B+ voltage is higher than 2.77 V, the difference between terminals A2B+ and A2B- is 0.2 V or less for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 2) circuit

·

Air fuel ratio sensor (bank 2 sensor 2)

·

ECM


Comes on SAE: P22B9
P22B817 A/F (O2) Sensor Positive Current Control Bank 2 Sensor 2 Circuit Voltage Above Threshold Difference between terminals A2B+ and A2B- is higher than 1.72 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 2) circuit

·

Air fuel ratio sensor (bank 2 sensor 2)

·

ECM


Comes on SAE: P22BA
P22BF11 A/F (O2) Sensor Negative Current Control Bank 2 Sensor 2 Circuit Short to Ground The A2B- voltage is 1.07 V or less for 5 seconds or more (2 trip detection logic).
·

Short in air fuel ratio sensor (bank 2 sensor 2) circuit

·

Air fuel ratio sensor (bank 2 sensor 2)

·

ECM


Comes on SAE: P22C0
P22BF12 A/F (O2) Sensor Negative Current Control Bank 2 Sensor 2 Circuit Short to Battery The A2B- voltage is higher than 4.59 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 2) circuit

·

Air fuel ratio sensor (bank 2 sensor 2)

·

ECM


Comes on SAE: P22C1

MONITOR DESCRIPTION

These DTCs are stored when there is an open or short in the air fuel ratio sensor (sensor 2) circuit, or the air fuel ratio sensor (sensor 2) output value is abnormal. The voltage of the air fuel ratio sensor (sensor 2) is monitored while the ignition switch is ON, or the impedance (impedance is an electrical term that indicates the difficulty of flow of current) is checked while engine running. If the voltage of the air fuel ratio sensor (sensor 2) is outside the normal range, or the impedance is outside the normal range, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Air fuel ratio sensor (sensor 2)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine and wait 5 minutes or more.

7.

Turn the GTS on.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P22AB11, P22AB12, P22AB13, P22AB16, P22AB17, P22B211, P22B212, P22B811,P22B812, P22B813, P22B816, P22B817, P22BF11 or P22BF12.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S2 or A/F (O2) Sensor Current B2S2].

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P22AB11, P22AB12, P22AB13, P22AB16, P22AB17, P22B211, P22B212 Bank 1
P22B811, P22B812, P22B813, P22B816, P22B817, P22BF11, P22BF12 Bank 2



PROCEDURE

1.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR (SENSOR 2) VOLTAGE)
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the air fuel ratio sensor (sensor 2) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C31,C32)Location & Routing

Click Connector(C31)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 1 Sensor 2)

Click Connector(C32)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 2 Sensor 2)

C31-3 (A1B+) - Body ground Ignition switch ON 2.8 to 3.2 V
C31-4 (A1B-) - Body ground Ignition switch ON 2.3 to 2.7 V
C31-3 (A1B+) - C31-4 (A1B-) Ignition switch ON 0.1 to 0.9 V
C32-3 (A2B+) - Body ground Ignition switch ON 2.8 to 3.2 V
C32-4 (A2B-) - Body ground Ignition switch ON 2.3 to 2.7 V
C32-3 (A2B+) - C32-4 (A2B-) Ignition switch ON 0.1 to 0.9 V



HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)

NG

2.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 2) - ECM)
2.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 2) - ECM)
a.

Disconnect the air fuel ratio sensor (sensor 2) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C31,C38,C32)Location & Routing

Click Connector(C31)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 1 Sensor 2)

Click Connector(C38)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C32)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 2 Sensor 2)

C31-1 (HA1B) - C38-6 (HA1B) Always Below 1 Ω
C31-3 (A1B+) - C38-50 (A1B+) Always Below 1 Ω
C31-4 (A1B-) - C38-49 (A1B-) Always Below 1 Ω
C32-1 (HA2B) - C38-5 (HA2B) Always Below 1 Ω
C32-3 (A2B+) - C38-48 (A2B+) Always Below 1 Ω
C32-4 (A2B-) - C38-47 (A2B-) Always Below 1 Ω
C31-1 (HA1B) or C38-6 (HA1B) - Body ground and other terminals Always 10 kΩ or higher
C31-3 (A1B+) or C38-50 (A1B+) - Body ground and other terminals Always 10 kΩ or higher
C31-4 (A1B-) or C38-49 (A1B-) - Body ground and other terminals Always 10 kΩ or higher
C32-1 (HA2B) or C38-5 (HA2B) - Body ground and other terminals Always 10 kΩ or higher
C32-3 (A2B+) or C38-48 (A2B+) - Body ground and other terminals Always 10 kΩ or higher
C32-4 (A2B-) or C38-47 (A2B-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR