Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P007A11  Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Ground  


DESCRIPTION

A293042E01
3.323,2.188 3.74,1.771 false 2,0.51 3.073,0.708 1.073,0.198 10 Resistance 1.604,0.229 2.677,0.427 1.073,0.198 10 Fig. 1: 2.115,0.792 3.188,0.99 1.073,0.198 10 [kΩ] 2.208,0.99 2.531,1.188 0.323,0.198 10 30 2.208,1.156 3.281,1.354 1.073,0.198 10 20 2.208,1.438 3.281,1.635 1.073,0.198 10 10 2.281,1.719 3.354,1.917 1.073,0.198 10 5 2.281,1.938 3.354,2.135 1.073,0.198 10 3 2.281,2.104 3.354,2.302 1.073,0.198 10 2 2.271,2.365 3.344,2.563 1.073,0.198 10 1 2.167,2.677 2.667,2.917 0.5,0.24 10 0.5 2.167,2.865 3.24,3.063 1.073,0.198 10 0.3 2.156,3.042 3.229,3.24 1.073,0.198 10 0.2 2.156,3.313 3.229,3.51 1.073,0.198 10 0.1 2.458,3.708 3.531,3.906 1.073,0.198 10 -20 2.833,3.708 3.906,3.906 1.073,0.198 10 0 3.104,3.708 4.177,3.906 1.073,0.198 10 20 3.427,3.708 4.5,3.906 1.073,0.198 10 40 3.729,3.708 4.802,3.906 1.073,0.198 10 60 4.052,3.708 5.125,3.906 1.073,0.198 10 80 4.313,3.708 5.385,3.906 1.073,0.198 10 100 4.802,3.708 5.875,3.906 1.073,0.198 10 [°C] 2.5,3.958 3.573,4.156 1.073,0.198 10 -4 2.802,3.958 3.875,4.156 1.073,0.198 10 32 3.115,3.958 4.188,4.156 1.073,0.198 10 68 3.396,3.958 3.76,4.281 0.365,0.323 10 104 3.698,3.958 4.094,4.292 0.396,0.333 10 140 4.021,3.958 4.417,4.292 0.396,0.333 10 176 4.333,3.958 4.729,4.292 0.396,0.333 10 212 4.781,3.969 5.854,4.167 1.073,0.198 10 [°F] 2.854,4.281 3.927,4.479 1.073,0.198 10 Temperature 3.771,1.625 4.844,1.823 1.073,0.198 10 Acceptable

The intake air temperature sensor, built into the No. 3 turbo pressure sensor, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THIM terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THIM also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P007A11 or P007A15 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 45°C (113°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P007A11 Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Ground The output voltage from the intake air temperature sensor is 0.1 V or less for 3 seconds or more (1 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (No. 3 turbo pressure sensor)

·

ECM


- SAE: P007C

HINT:

When a DTC is output, check the Data List item "Intake Air Temperature B1S1 (Turbo)" using the GTS.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

DTC No. Intake Air Temperature B1S1 (Turbo) Malfunction
P007A11 140°C (284°F) Short in THIM circuit to ground

If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM calculates the intake manifold internal temperature from the intake air temperature sensor output voltage. If the intake air temperature sensor output voltage is outside the normal range, there may be a malfunction or open or short circuit in the intake air temperature sensor. In this case, the ECM stores a DTC.

Example:

When the sensor output voltage is 0.1 V or less for 3 seconds or more, the ECM stores DTC P007A11.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P007A11.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A403540E20
0.417,2.667 0.865,2.969 0.448,0.302 10 false C40 0.406,2.865 2.302,3.292 1.896,0.427 10 false Intake Air Temperature Sensor (No. 3 Turbo Pressure Sensor) 2.198,1.323 2.438,1.563 0.24,0.24 10 false 4 1.917,1.938 2.229,2.135 0.313,0.198 10 false E2 2.219,1.927 2.375,2.125 0.156,0.198 10 false 2 5,1.333 5.344,1.625 0.344,0.292 10 false 37 5.292,1.333 5.875,1.646 0.583,0.313 10 false THIM 5.854,1.229 6.083,1.51 0.229,0.281 10 false R 5.896,0.938 6.313,1.177 0.417,0.24 10 false 5 V 5,1.927 5.313,2.26 0.313,0.333 10 false 39 5.281,1.927 5.802,2.219 0.521,0.292 10 false EPIM 5.688,2.979 6.083,3.25 0.396,0.271 10 false C38 5.698,3.146 6.156,3.344 0.458,0.198 10 false ECM 1.76,1.323 2.344,1.635 0.583,0.313 10 false THIM

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A226261C58
0.823,1.74 1.5,2.063 0.677,0.323 10 false *1 2.646,1.74 3.167,1.896 0.521,0.156 10 false *2 1.01,0.708 1.531,0.99 0.521,0.281 10 false THIM 1.948,1 2.698,1.208 0.75,0.208 10 false EPIM 1.969,0.656 2.49,0.938 0.521,0.281 10 false THIM 1.156,1.042 1.906,1.25 0.75,0.208 10 false E2
*1 No. 3 turbo pressure sensor
*2 ECM


Disconnect the No. 3 turbo pressure sensor connector.


b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S1 (Turbo)
50003 372 310
Standard value:

140°C (284°F)



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (NO. 3 TURBO PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (NO. 3 TURBO PRESSURE SENSOR - ECM)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR