Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P012A11  Turbocharger/Supercharger Inlet Pressure Sensor "A" Circuit Low Circuit Short to Ground  P237411  Turbocharger/Supercharger Inlet Pressure Sensor "B" Circuit Low Circuit Short to Ground  


DESCRIPTION

The internal sensor in the No. 1 turbo pressure sensor detects the air inlet duct internal pressure as a voltage.

A409083E01
1.125,0.281 3.188,0.521 2.063,0.24 10 false Air inlet duct internal pressure 0.073,0.063 0.865,0.354 0.792,0.292 10 false Voltage (V) 3.052,2.385 3.406,2.677 0.354,0.292 10 false kPa 3.052,2.896 3.344,3.24 0.292,0.344 10 false psi 0.229,0.719 0.583,1.01 0.354,0.292 10 false 4.2 0.229,0.938 0.583,1.229 0.354,0.292 10 false 3.6 0.24,1.531 0.594,1.823 0.354,0.292 10 false 2.4 0.24,1.99 0.594,2.281 0.354,0.292 10 false 1.2 2.583,2.542 3.083,2.75 0.5,0.208 10 false 119.99 2.188,2.542 2.573,2.75 0.385,0.208 10 false 99.99 1.469,2.531 1.854,2.74 0.385,0.208 10 false 59.99 0.854,2.531 1.24,2.74 0.385,0.208 10 false 19.99 0.896,3.031 1.24,3.26 0.344,0.229 10 false 2.90 1.5,3.031 1.844,3.26 0.344,0.229 10 false 8.70 2.177,3.031 2.583,3.271 0.406,0.24 10 false 13.05 2.604,3.031 3.031,3.26 0.427,0.229 10 false 17.40

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P012A11 Turbocharger/Supercharger Inlet Pressure Sensor "A" Circuit Low Circuit Short to Ground The output voltage from the No. 1 turbo pressure sensor (bank 1) is below 0.6 V for 3 seconds or more (1 trip detection logic).
·

Open or short in No. 1 turbo pressure sensor (bank 1) circuit

·

No. 1 turbo pressure sensor (bank 1)

·

ECM


- SAE: P012C
P237411 Turbocharger/Supercharger Inlet Pressure Sensor "B" Circuit Low Circuit Short to Ground The output voltage from the No. 1 turbo pressure sensor (bank 2) is below 0.6 V for 3 seconds or more (1 trip detection logic).
·

Open or short in No. 1 turbo pressure sensor (bank 2) circuit

·

No. 1 turbo pressure sensor (bank 2)

·

ECM


- SAE: P2376

HINT:

When a DTC is output, check the Data List item "Turbocharger/Supercharger Inlet Pressure Bank1 and Turbocharger/Supercharger Inlet Pressure Bank2" using the GTS.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

DTC No. Turbocharger/Supercharger Inlet Pressure Bank1 or Turbocharger/Supercharger Inlet Pressure Bank2 Malfunction
P012A11 Approximately 0 kPa [0 psi]
·

Short in PIC circuit to ground

·

Short in PIC circuit to EPIC circuit

·

Open in VCPC circuit


P237411
·

Short in PIC2 circuit to ground

·

Short in PIC2 circuit to EPC2 circuit

·

Open in VPC2 circuit



If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM calculates the air inlet duct internal pressure from the No. 1 turbo pressure sensor output voltage. If the No. 1 turbo pressure sensor output voltage is not within the normal range, there may be a malfunction in the No. 1 turbo pressure sensor or an open or short circuit. In this case, the ECM stores a DTC.

Example:

When the sensor output voltage is below 0.6 V for 3 seconds or more, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P012A11 or P237411.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A480729E01
4.854,0.479 5.469,0.677 0.615,0.198 10 false VCPC 4.844,1.552 5.458,1.75 0.615,0.198 10 false EPIC 4.854,1.021 5.469,1.219 0.615,0.198 10 false PIC 6.094,0.333 6.708,0.531 0.615,0.198 10 false 5 V 6.021,0.917 6.635,1.115 0.615,0.198 10 false 180 kΩ 5.531,3.563 6.146,3.76 0.615,0.198 10 false 180 kΩ 4.844,3.698 5.458,3.896 0.615,0.198 10 false PIC2 5.667,5 6.281,5.198 0.615,0.198 10 false C38 5.677,5.188 6.292,5.385 0.615,0.198 10 false ECM 1.667,1.156 1.958,1.365 0.292,0.208 10 false PIC 1.615,3.833 1.958,4.031 0.344,0.198 10 false PIC2 1.698,0.615 1.958,0.823 0.26,0.208 10 false VC 1.646,3.271 1.99,3.458 0.344,0.188 10 false VC2 1.719,1.708 1.99,1.906 0.271,0.198 10 false E2 1.635,4.344 1.948,4.521 0.313,0.177 10 false E22 4.51,0.479 4.781,0.688 0.271,0.208 10 false 46 4.51,1.031 4.781,1.24 0.271,0.208 10 false 42 4.51,1.552 4.781,1.76 0.271,0.208 10 false 45 0.438,2.083 0.708,2.292 0.271,0.208 10 false C23 0.438,4.729 0.708,4.938 0.271,0.208 10 false C22 0.438,2.26 3.094,2.583 2.656,0.323 10 false No. 1 Turbo Pressure Sensor (Bank 1) 2.073,0.479 2.344,0.688 0.271,0.208 10 false 3 2.063,1.031 2.333,1.24 0.271,0.208 10 false 2 2.052,1.563 2.323,1.771 0.271,0.208 10 false 1 2.104,3.156 2.375,3.365 0.271,0.208 10 false 3 2.104,3.688 2.375,3.896 0.271,0.208 10 false 2 2.094,4.24 2.365,4.448 0.271,0.208 10 false 1 0.427,4.927 3.094,5.208 2.667,0.281 10 false No. 1 Turbo Pressure Sensor (Bank 2) 4.542,3.156 4.813,3.365 0.271,0.208 10 false 44 4.844,3.167 5.458,3.365 0.615,0.198 10 false VPC2 4.542,3.698 4.813,3.906 0.271,0.208 10 false 41 4.531,4.229 4.802,4.438 0.271,0.208 10 false 43 4.844,4.24 5.458,4.438 0.615,0.198 10 false EPC2

CAUTION / NOTICE / HINT

HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P012A11 Bank 1
P237411 Bank 2



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the No. 1 turbo pressure sensor connector.


b.

Turn the ignition switch to ON.



d.

Turn the ignition switch off and wait for at least 30 seconds.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 TURBO PRESSURE SENSOR

NG

2.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the No. 1 turbo pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR