Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P023A13  Charge Air Cooler Coolant Pump Control Circuit Open  


DESCRIPTION

Refer to DTC P023A12.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P023A12

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P023A13 Charge Air Cooler Coolant Pump Control Circuit Open The speed of the electric coolant pump calculated from the IWPI signal is less than 10 rpm (open or short in the IWPI circuit) (1 trip detection logic).
·

Open or short in electric water pump assembly circuit

·

Electric water pump assembly

·

EFI MAIN NO. 3 relay

·

ECM


- SAE: P023A

Related Data List
DTC No. Data List
P023A13
·

Intercooler Water Pump Speed

·

Intercooler Water Pump



MONITOR DESCRIPTION

The ECM receives a frequency signal (IWPI) from the electric water pump assembly and calculates the speed of the electric water pump assembly. As the frequency signal (IWPI) is 4 Hz when the electric water pump assembly is stopped to enable the ECM to detect an open or short in the signal line, the electric water pump assembly speed will be displayed as approximately 160 rpm even when the pump is stopped. If the electric water pump assembly speed is calculated to be less than 10 rpm, the ECM judges that there is an open or short in the IWPI circuit and stores this DTC.

CONFIRMATION DRIVING PATTERN

1.
A330723E40
3.042,1.854 2.635,1.344 2.635,1.344 2.438,1.344 false 0.25,0.292 1.354,0.542 1.104,0.25 10 false Vehicle Speed 0.76,0.677 1.375,0.875 0.615,0.198 10 false 50 km/h 0.927,2.042 1.542,2.24 0.615,0.198 10 false Idling 0.417,2.385 1.333,2.771 0.917,0.385 10 false Ignition switch ON 5.625,3.375 5.99,3.625 0.365,0.25 10 false [C] 1.427,1.26 2.729,1.563 1.302,0.302 10 false Fully depressed 2.198,1.885 2.656,2.083 0.458,0.198 10 false [A] 3.313,1.219 3.792,1.417 0.479,0.198 10 false [B]

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON.

4.

Turn the GTS on.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON.

8.

Turn the GTS on.

9.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

10.

Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].

NOTICE:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P023A13.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTERCOOLER WATER PUMP)
a.

Perform the Active Test. Check that the electric water pump assembly is operating (vibrating).

Powertrain > Engine > Active Test
Tester Display
Control the Intercooler Water Pump
50004 372 9
OK:

The electric water pump assembly is operating (vibrating).


HINT:

Use a sound scope if the operation is difficult to check.



Result:
Proceed to
OK
NG



OK

2.CHECK ECM (IWPI VOLTAGE)

NG

4.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - BODY GROUND)
2.CHECK ECM (IWPI VOLTAGE)
a.

Disconnect the electric water pump assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B29)Location & Routing

Click Connector(B29)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Electric Water Pump Assembly

B29-2 (NWP) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRIC WATER PUMP ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)
a.

Disconnect the electric water pump assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B29,B1)Location & Routing

Click Connector(B29)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Electric Water Pump Assembly

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B29-2 (NWP) - B1-38 (IWPI) Always Below 1 Ω
B29-2 (NWP) or B1-38 (IWPI) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the electric water pump assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B29)Location & Routing

Click Connector(B29)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Electric Water Pump Assembly

B29-1 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT EFI MAIN NO. 3 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT EFI MAIN NO. 3 RELAY

OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ELECTRIC WATER PUMP ASSEMBLY)

NG

REPLACE EFI MAIN NO. 3 RELAY

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ELECTRIC WATER PUMP ASSEMBLY)
a.

Disconnect the electric water pump assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B29)Location & Routing

Click Connector(B29)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Electric Water Pump Assembly

B29-4 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRIC WATER PUMP ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF EFI MAIN NO. 3 RELAY)
7.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF EFI MAIN NO. 3 RELAY)
a.
A485839C01
0.125,0.125 0.438,0.281 0.313,0.156 10 false *1 2.448,1.313 2.76,1.469 0.313,0.156 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 EFI MAIN NO. 3 Relay


Remove the EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI MAIN NO. 3 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI MAIN NO. 3 RELAY)

8.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - BODY GROUND)
a.

Remove the EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI MAIN NO. 3 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - ELECTRIC WATER PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - ELECTRIC WATER PUMP ASSEMBLY)
a.

Remove the EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the electric water pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B29)Location & Routing

Click Connector(B29)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Electric Water Pump Assembly

5 (EFI MAIN NO. 3 relay) - B29-4 (+B) Always Below 1 Ω
5 (EFI MAIN NO. 3 relay) or B29-4 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN NO. 1 RELAY - EFI MAIN NO. 3 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR