When the ignition switch is turned to ON, the battery voltage is applied to IGP of the ECM. When the transistor in the MREL circuit operates, current flows from the battery to ground through the drive circuit of the EFI MAIN NO. 1 relay, thus operating the relay which supplies power to the +B, +B2 and +B3 terminals of the ECM.
Inspect the fuses for circuits related to this system before performing the following procedure.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B1)Location & Routingewd_type=routing;type=c;code=B1 |
||
| B1-9 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B1)Location & Routingewd_type=routing;type=c;code=B1 |
||
| B1-8 (IGP) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Remove the EFI MAIN NO. 1 relay, EFI MAIN NO. 2 relay, IGT/INJ relay, A/F relay and EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.
Remove the EFI MAIN NO. 2 relay, IGT/INJ relay, A/F relay and EFI MAIN NO. 3 relay connected between the checked terminals as the coil inside the relay influences the measurement value.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B1,C38)Location & Routingewd_type=routing;type=c,c;code=B1,C38 |
||
| 2 (EFI MAIN NO. 1 relay) - B1-3 (MREL) | Always | Below 1 Ω |
| 5 (EFI MAIN NO. 1 relay) - C38-12 (+B) | Always | Below 1 Ω |
| 5 (EFI MAIN NO. 1 relay) - C38-11 (+B2) | Always | Below 1 Ω |
| 5 (EFI MAIN NO. 1 relay) - C38-10 (+B3) | Always | Below 1 Ω |
| 2 (EFI MAIN NO. 1 relay) or B1-3 (MREL) - Body ground and other terminals | Always | 10 kΩ or higher |
| 5 (EFI MAIN NO. 1 relay), C38-12 (+B), C38-11 (+B2) or C38-10 (+B3) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 2 Engine Room Relay Block and Junction Block Assembly |
| *2 | EFI MAIN NO. 1 Relay |
Remove the EFI MAIN NO. 1 relay from the No. 2 engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (EFI MAIN NO. 1 relay) - Body ground | Always | 11 to 14 V |
| 1 (EFI MAIN NO. 1 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Remove the IGP NO. 2 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B1)Location & Routingewd_type=routing;type=c;code=B1 |
||
| 5 (IGP NO. 2 relay) - B1-8 (IGP) | Always | Below 1 Ω |
| 5 (IGP NO. 2 relay) or B1-8 (IGP) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 2 Engine Room Relay Block and Junction Block Assembly |
| *2 | IGP NO. 2 Relay |
Remove the IGP NO. 2 relay from the No. 2 engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (IGP NO. 2 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IGP NO. 2 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (IGP NO. 2 relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IGP NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Remove the IGP NO. 2 relay from the No. 2 engine room relay block and junction block assembly.
Remove the IGP NO. 3 relay from the No. 1 luggage room relay block and junction block assembly.
Remove the IGP NO. 3 relay connected between the checked terminals as the coil inside the relay influences the measurement value.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (IGP NO. 1 relay) - 1 (IGP NO. 2 relay) | Always | Below 1 Ω |
| 5 (IGP NO. 1 relay) or 1 (IGP NO. 2 relay) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | IGP NO. 1 Relay |
Remove the IGP NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (IGP NO. 1 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IGP NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (IGP NO. 1 relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IGP NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I40)Location & Routingewd_type=routing;type=c;code=I40 |
||
| I40-24 (IGPD) - 1 (IGP NO. 1 relay) | Always | Below 1 Ω |
| I40-24 (IGPD) or 1 (IGP NO. 1 relay) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG