Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P00CF62  Barometric Pressure - Turbocharger / Supercharger Boost Sensor "A" Signal Compare Failure  


DESCRIPTION

At ignition switch ON or during idling, the No. 2 turbo pressure sensor and the atmospheric pressure sensor built into the ECM are at atmospheric pressure and their outputs match.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P00CF62 Barometric Pressure - Turbocharger / Supercharger Boost Sensor "A" Signal Compare Failure 15 kPa [2.18 psi] or greater difference between the atmospheric pressure values of the No. 2 turbo pressure sensor and the atmospheric pressure sensor (1 trip detection logic).
·

No. 2 turbo pressure sensor

·

Wire harness or connector

·

ECM


Comes on SAE: P00CF

MONITOR DESCRIPTION

At ignition switch ON or during idling, the output values from the No. 2 turbo pressure sensor and the atmospheric pressure sensor built into the ECM are compared. If the difference in atmospheric pressure values is 15 kPa [2.18 psi] or greater, there may be a malfunction in the No. 2 turbo pressure sensor and atmospheric pressure sensor. In this case, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components No. 2 turbo pressure sensor
Atmospheric pressure sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P00CF62.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P00CF62)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P00CF62 is output A
P00CF62 and P02351C, P211900, P211904 or P211977 are output
P00CF62 and P02351C, P211900, P211904 or P211977 and other DTCs are output B


HINT:

If any DTCs other than P00CF62 and P02351C, P211900, P211904 or P211977 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (BOOST PRESSURE SENSOR AND ATMOSPHERIC PRESSURE)

B

GO TO DTC CHART

2.READ VALUE USING GTS (BOOST PRESSURE SENSOR AND ATMOSPHERIC PRESSURE)
a.

Compare Atmospheric Pressure and Boost Pressure Sensor in the Data List.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
Boost Pressure Sensor
50003 372 229,269

Result:
Result Proceed to
Difference between Atmospheric Pressure and Boost Pressure Sensor in the Data List exceeds 15 kPa [2.18 psi] A
Other than above B



A

3.READ VALUE USING GTS (BOOST PRESSURE SENSOR AND ATMOSPHERIC PRESSURE)

B

6.CHECK INTAKE SYSTEM
3.READ VALUE USING GTS (BOOST PRESSURE SENSOR AND ATMOSPHERIC PRESSURE)
a.

Using the table, read the normal atmospheric pressure value for the applicable altitude and temperature.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
Boost Pressure Sensor
50003 372 229,269
A479641C01
0.177,0.063 0.49,0.26 0.313,0.198 10 false *a 0.396,0.51 0.708,0.708 0.313,0.198 10 false *b 2.719,0.51 3.031,0.708 0.313,0.198 10 false *b 5.031,0.51 5.344,0.708 0.313,0.198 10 false *b 1.146,0.51 1.458,0.708 0.313,0.198 10 false *c 3.438,0.5 3.75,0.698 0.313,0.198 10 false *c 5.729,0.5 6.042,0.698 0.313,0.198 10 false *c 1.802,0.5 2.115,0.698 0.313,0.198 10 false *d 4.125,0.51 4.438,0.708 0.313,0.198 10 false *d 6.396,0.521 6.708,0.719 0.313,0.198 10 false *d
*a Altitude, Temperature and Atmospheric Pressure Correlation Table *b Altitude (m (ft.))
*c Temperature (°C (°F)) *d Atmospheric Pressure (kPa (psi))


HINT:
·

Standard atmospheric pressure is approximately 101 kPa(abs) [14.65 psi(abs)].

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa [0.15 psi]. This varies by weather.




b.

Compare the Atmospheric Pressure and Boost Pressure Sensor values in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Difference between (difference between Boost Pressure Sensor in the Data List and normal atmospheric pressure) and (difference between Atmospheric Pressure in the Data List and normal atmospheric pressure) is 4 kPa [0.58 psi] or greater A
Other than above B


HINT:
·

As the table below shows reference values only, use actual values for calculations.

·

In Example 1, as the pressure difference is 4 kPa [0.58 psi] or higher, proceed to the next step.

·

In Example 2, as the pressure difference is less than 4 kPa [0.58 psi], replace the ECM.



Item Example 1 Example 2
Atmospheric pressure Difference to normal atmospheric pressure Difference between (difference between Boost Pressure Sensor in the Data List and normal atmospheric pressure) and (difference between Atmospheric Pressure in the Data List and normal atmospheric pressure) Atmospheric pressure Difference to normal atmospheric pressure Difference between (difference between Boost Pressure Sensor in the Data List and normal atmospheric pressure) and (difference between Atmospheric Pressure in the Data List and normal atmospheric pressure)
Normal atmospheric pressure 100 kPa(abs) [15.5 psi(abs)] - 6 kPa [0.87 psi] 100 kPa(abs) [15.5 psi(abs)] - 2 kPa [0.29 psi]
Boost Pressure Sensor in the Data List 110 kPa(abs) [15.95 psi(abs)] 10 kPa [1.45 psi] 108 kPa(abs) [15.66 psi(abs)] 8 kPa [1.16 psi]
Atmospheric Pressure in the Data List 96 kPa(abs) [13.92 psi(abs)] 4 kPa [0.58 psi] 94 kPa(abs) [13.63 psi(abs)] 6 kPa [0.87 psi]



A

4.CHECK HARNESS AND CONNECTOR

B

4.CHECK HARNESS AND CONNECTOR
a.

Disconnect the No. 2 turbo pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C21)Location & Routing

Click Connector(C21)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 1 Turbo Pressure Sensor RH

C21-3 (VC) - C21-1 (E2) Ignition switch ON 4.5 to 5.5 V
C21-2 (PTA) - C21-1 (E2) Ignition switch ON 3.0 to 5.5 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C21)Location & Routing

Click Connector(C21)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 1 Turbo Pressure Sensor RH

C21-3 (VC) - C21-2 (PTA) Ignition switch off 171 to 189 kΩ
C21-1 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (NO. 2 TURBO PRESSURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (NO. 2 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the No. 2 turbo pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C21,C37)Location & Routing

Click Connector(C21)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 1 Turbo Pressure Sensor RH

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C21-3 (VC) - C37-92 (VPTA) Always Below 1 Ω
C21-1 (E2) - C37-91 (EPTA) Always Below 1 Ω
C21-2 (PTA) - C37-111 (PTA) Always Below 1 Ω
C21-3 (VC) or C37-92 (VPTA) - Body ground and other terminals Always 10 kΩ or higher
C21-2 (PTA) or C37-111 (PTA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK INTAKE SYSTEM
a.

Check that there is no air suction or blockage at any points in the intake system.

Click hereEngine / Hybrid System>V35A-FTS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No air suction or blockage.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P00CF62)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P00CF62)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Perform the All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 1020

c.

Input the DTC: P00CF62.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(P00CF62 is output)
B




A

END

B