Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P15AD87  Active Grille Air Shutter "A" Missing Message  


DESCRIPTION

The ECM and swing grille actuator assembly each detect reception malfunctions. Swing grille actuator assembly reception malfunctions detected by the swing grille actuator assembly are sent to the ECM via LIN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P15AD87 Active Grille Air Shutter "A" Missing Message ECM or swing grille actuator assembly communication stops for 15.5 seconds or more with the ignition switch ON (2 trip detection logic).
·

Wire harness or connector

·

Radiator shutter assembly


- SAE: P15AD

MONITOR DESCRIPTION

When a communication malfunction occurs in either the ECM or swing grille actuator assembly, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Swing grille actuator assembly
ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 30 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P15AD87.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A485837E02
0.729,4.104 1.438,4.375 0.708,0.271 10 false Battery 0.521,3.354 1.719,3.635 1.198,0.281 10 false SUB R/B-NO. 1 0.49,2.729 1.604,3 1.115,0.271 10 false EFI MAIN NO. 1 1.51,3.01 2.625,3.281 1.115,0.271 10 false EFI NO. 2 5.76,2.833 6.344,3.042 0.583,0.208 10 false MREL 2.052,3.208 3.167,3.479 1.115,0.271 10 false EFI MAIN NO. 1 0.573,0.583 1.688,0.854 1.115,0.271 10 false EFI MAIN NO. 3 1.938,0.979 3.052,1.25 1.115,0.271 10 false EFI MAIN NO. 3 3.125,1.365 4.24,1.635 1.115,0.271 10 false EFI-B NO. 4 5.771,1.031 6.302,1.219 0.531,0.188 10 false LIN 3.24,0.552 3.76,1.104 0.521,0.552 10 false GRILLE SHUTT 3.917,2.156 5.219,2.563 1.302,0.406 10 false Swing Grille Actuator Assembly 4.167,0.375 4.573,0.656 0.406,0.281 10 false +B 4.156,1.646 4.604,1.885 0.448,0.24 10 false GND 5.448,2.844 6.031,3.052 0.583,0.208 10 false B1 6.156,3.583 6.74,3.792 0.583,0.208 10 false ECM 5.469,2.656 5.615,2.844 0.146,0.188 10 false 3 5.458,0.844 5.646,1.042 0.188,0.198 10 false 17 5.021,0.896 5.167,1.083 0.146,0.188 10 false 2 3.979,1.51 4.125,1.698 0.146,0.188 10 false 1 3.948,0.25 4.094,0.438 0.146,0.188 10 false 3 2.875,0.26 3.021,0.448 0.146,0.188 10 false 5 2.875,2.438 3.021,2.625 0.146,0.188 10 false 5 2.875,0.531 3.021,0.719 0.146,0.188 10 false 2 2.875,2.729 3.021,2.917 0.146,0.188 10 false 2 2.031,0.26 2.177,0.448 0.146,0.188 10 false 3 2.052,2.438 2.198,2.625 0.146,0.188 10 false 3 2.042,0.552 2.188,0.74 0.146,0.188 10 false 1 2.052,2.719 2.198,2.906 0.146,0.188 10 false 1 3.927,1.979 4.51,2.188 0.583,0.208 10 false B21 4.688,1.031 5.219,1.219 0.531,0.188 10 false LIN 5.417,1.031 6,1.24 0.583,0.208 10 false C38

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

In order to ensure safety, before performing troubleshooting or removing the radiator shutter assembly, change the grille shutter control mode to maintenance mode.



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM UTILITY USING GTS (SWITCH GRILLE SHUTTER CONTROL MODE)
a.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 5672

Result:
Proceed to
NEXT



NEXT

2.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - ECM)
a.

Disconnect the swing grille actuator assembly connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SWING GRILLE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SWING GRILLE ACTUATOR ASSEMBLY)
a.

Disconnect the swing grille actuator assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B21)Location & Routing

Click Connector(B21)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Radiator Shutter Assembly

B21-3 (+B) - B21-1 (GND) Ignition switch ON 11 to 14 V



HINT:

Perform "Switch Grille Shutter Control Mode and Grille Shutter Initialization" after replacing the radiator shutter assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

REPLACE RADIATOR SHUTTER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the swing grille actuator assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B21)Location & Routing

Click Connector(B21)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Radiator Shutter Assembly

B21-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT EFI MAIN NO. 3 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT EFI MAIN NO. 3 RELAY

OK

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF EFI MAIN NO. 3 RELAY)

NG

REPLACE EFI MAIN NO. 3 RELAY

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF EFI MAIN NO. 3 RELAY)
a.
A485839C01
0.125,0.125 0.438,0.281 0.313,0.156 10 false *1 2.448,1.313 2.76,1.469 0.313,0.156 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 EFI MAIN NO. 3 Relay


Remove the EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI MAIN NO. 3 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI MAIN NO. 3 RELAY)

7.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - BODY GROUND)
a.

Remove the EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI MAIN NO. 3 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - SWING GRILLE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - SWING GRILLE ACTUATOR ASSEMBLY)
a.

Remove the EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the swing grille actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B21)Location & Routing

Click Connector(B21)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Radiator Shutter Assembly

5 (EFI MAIN NO. 3 relay) - B21-3 (+B) Always Below 1 Ω
5 (EFI MAIN NO. 3 relay) or B21-3 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK ECM POWER SOURCE CIRCUIT

NEXT

10.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
10.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
a.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 5672

b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Grille Shutter Control Mode
50003 372 1304
Standard:
GTS Display Specified Condition
Grille Shutter Control Mode Normal


Result:
Proceed to
NEXT




NEXT

END