Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P052631  Fan Speed Sensor Circuit No Signal No Signal  


DESCRIPTION

The fan speed sensor is provided inside the fluid coupling assembly and outputs 6 signals per fan rotation.

The ECM detects the fan speed from the pulse width of fan speed sensor signals.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P052631 Fan Speed Sensor Circuit No Signal No Signal When the engine is running (at 600 rpm or higher) and the fan control solenoid drive duty ratio is 10% or more, the fan speed sensor signal is not input for 10 seconds or more
(1 trip detection logic)
·

Fan speed sensor (fluid coupling assembly)

·

Wire harness or connector

·

ECM


- SAE: P0528

MONITOR DESCRIPTION

When the engine is running (at 600 rpm or higher) and the fan control solenoid drive duty ratio is 10% or more, the ECM stores a DTC if a fan speed sensor signal is not input.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine [A].

7.

Wait 2 minutes or more [B].

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P052631.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform steps [A] through [C] again.




WIRING DIAGRAM

A480727E01
5.583,3.198 6.042,3.396 0.458,0.198 10 false ECM 5.573,3.021 6.031,3.219 0.458,0.198 10 false C37 5.896,0.479 6.354,0.677 0.458,0.198 10 false 5 V 5.885,1.198 6.344,1.396 0.458,0.198 10 false 5 V 4.885,0.74 5.344,0.938 0.458,0.198 10 false VCF 4.896,1.5 5.354,1.698 0.458,0.198 10 false NCF 4.885,2.146 5.344,2.344 0.458,0.198 10 false ECF 4.469,0.729 4.927,0.927 0.458,0.198 10 false 113 4.469,1.5 4.927,1.698 0.458,0.198 10 false 108 4.479,2.135 4.938,2.333 0.458,0.198 10 false 112 1.219,0.865 1.677,1.063 0.458,0.198 10 false VCFC 1.208,1.615 1.667,1.813 0.458,0.198 10 false NCFC 1.229,2.25 1.688,2.448 0.458,0.198 10 false E1FC 0.594,2.604 1.052,2.802 0.458,0.198 10 false C8 0.615,2.792 3.552,3.156 2.938,0.365 10 false Fan Speed Sensor (Fluid Coupling Assembly) 1.771,0.729 2.229,0.927 0.458,0.198 10 false 4 1.771,1.49 2.229,1.688 0.458,0.198 10 false 5 1.771,2.115 2.229,2.313 0.458,0.198 10 false 6

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FAN SPEED SENSOR (FLUID COUPLING ASSEMBLY))
a.

Disconnect the fan speed sensor (fluid coupling assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C8)Location & Routing

Click Connector(C8)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Fluid Coupling Assembly

C8-4 (VCFC) - C8-6 (E1FC) Ignition switch ON 4.5 to 5.5 V
C8-5 (NCFC) - C8-6 (E1FC) Ignition switch ON 4.5 to 5.5 V


Result:
Proceed to
OK
NG




OK

2.REPLACE FAN SPEED SENSOR (FLUID COUPLING ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (FAN SPEED SENSOR (FLUID COUPLING ASSEMBLY) - ECM)
2.REPLACE FAN SPEED SENSOR (FLUID COUPLING ASSEMBLY)
HINT:

Click hereEngine / Hybrid System>V35A-FTS (COOLING)>RADIATOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P052631)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P052631)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P052631 is output B




A

END

B

5.CHECK HARNESS AND CONNECTOR (FAN SPEED SENSOR (FLUID COUPLING ASSEMBLY) - ECM)
a.

Disconnect the fan speed sensor (fluid coupling assembly) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C8,C37)Location & Routing

Click Connector(C8)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Fluid Coupling Assembly

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C8-4 (VCFC) - C37-113 (VCF) Always Below 1 Ω
C8-5 (NCFC) - C37-108 (NCF) Always Below 1 Ω
C8-6 (E1FC) - C37-112 (ECF) Always Below 1 Ω
C8-4 (VCFC) or C37-113 (VCF) - Body ground and other terminals Always 10 kΩ or higher
C8-5 (NCFC) or C37-108 (NCF) - Body ground and other terminals Always 10 kΩ or higher
C8-6 (E1FC) or C37-112 (ECF) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR