Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P253314  Ignition Switch On/Start Position Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

When the ignition switch is turned to ON, the battery power source is supplied to the IGP and IGR terminals of the ECM. When the ignition switch is off, the battery power source is cut off.

When the ignition switch is turned off during driving, the battery power source supplied to the IGP terminal is cut off. However, the battery power source supplied to the IGR terminal is supplied until the vehicle is stopped and the ignition switch is turned off.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P253314 Ignition Switch On/Start Position Circuit Low Circuit Short to Ground or Open Short to ground or open in IGR terminal circuit (2 trip detection logic).
·

IGR NO. 3 RELAY

·

Wire harness or connector

·

ECM


- SAE: P2534

MONITOR DESCRIPTION

The ECM stores a DTC when there is no battery voltage to the IGR terminal even though there is battery voltage to the IGP terminal.

WIRING DIAGRAM

A485844E02
0.729,6.865 1.646,7.063 0.917,0.198 10 false Battery 0.563,5.885 1.698,6.156 1.135,0.271 10 false SUB R/B-NO. 1 4.677,5.875 5.729,6.188 1.052,0.313 10 false ENG-IGP NO. 1 6.115,6.219 6.74,6.531 0.625,0.313 10 false E1 6.104,5.719 6.729,6.031 0.625,0.313 10 false IGP 0.563,4.948 1.344,5.25 0.781,0.302 10 false MAIN R/B 0.844,0.615 1.469,0.927 0.625,0.313 10 false PDB-B 6.104,0.833 6.729,1.146 0.625,0.313 10 false IGPD 6.104,0.417 6.729,0.729 0.625,0.313 10 false +B 6.104,1.25 6.729,1.563 0.625,0.313 10 false IGRD 3.896,3.854 4.646,4.167 0.75,0.313 10 false IGR NO. 3 6.104,3.073 6.729,3.385 0.625,0.313 10 false IGR 6.344,6.74 6.969,7.052 0.625,0.313 10 false B1 6.344,6.906 6.781,7.146 0.438,0.24 10 false ECM 5.594,1.74 7.115,2.271 1.521,0.531 10 false Certification ECU (smart key ECU assembly) 5.802,1.229 6.427,1.542 0.625,0.313 10 false I40 5.792,0.823 6.417,1.135 0.625,0.313 10 false I40 5.792,0.427 6.417,0.74 0.625,0.313 10 false I39 5.844,0.219 6.469,0.531 0.625,0.313 10 false 6 5.781,1.042 6.406,1.354 0.625,0.313 10 false 11 5.802,0.635 6.427,0.948 0.625,0.313 10 false 24 1.677,6.01 2.302,6.323 0.625,0.313 10 false 2 2.542,5.99 3.167,6.302 0.625,0.313 10 false 1 2.542,5.573 3.167,5.885 0.625,0.313 10 false 5 1.688,5.563 2.313,5.875 0.625,0.313 10 false 3 5.875,2.917 6.5,3.229 0.625,0.313 10 false 7 5.885,5.583 6.51,5.896 0.625,0.313 10 false 8 5.896,6.083 6.521,6.396 0.625,0.313 10 false 9 1.573,0.594 2.26,0.875 0.688,0.281 10 false SMART 3.552,5.01 4.604,5.323 1.052,0.313 10 false ECU-IGP NO. 3 1.844,6.458 2.896,6.771 1.052,0.313 10 false IGP NO. 2 1.823,4.906 2.875,5.219 1.052,0.313 10 false IGP NO. 1 1.688,3.979 1.906,4.219 0.219,0.24 10 false 3 2.5,3.958 2.708,4.177 0.208,0.219 10 false 5 2.51,4.417 2.74,4.646 0.229,0.229 10 false 1 1.677,4.438 1.958,4.667 0.281,0.229 10 false 2 4.813,3.24 5.865,3.552 1.052,0.313 10 false ENG-IGR NO. 1 3.75,3.406 4.031,3.635 0.281,0.229 10 false 1 4.573,3.406 4.802,3.635 0.229,0.229 10 false 2 3.75,2.885 3.969,3.125 0.219,0.24 10 false 3 4.583,2.896 4.792,3.115 0.208,0.219 10 false 5 0.146,5.396 0.375,5.625 0.229,0.229 10 false *1 0.531,5.406 0.76,5.635 0.229,0.229 10 false *2 0.531,4.479 0.76,4.708 0.229,0.229 10 false *2 3.167,6.906 4.167,7.146 1,0.24 10 false *1: for LHD 3.167,7.24 4.167,7.479 1,0.24 10 false *2: for RHD

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 1 minute or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P253314

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system is malfunctioning.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (IGR)
a.

Read the Data List.

Powertrain > Engine > Data List
Tester Display
IGR
50003 372 1232
Result:
Result Proceed to
The value of IGR is ON A
None of the above conditions are met B




A

B

2.CHECK TERMINAL VOLTAGE (IGR VOLTAGE)
2.CHECK TERMINAL VOLTAGE (IGR VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B1-7 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT IGR NO. 3 RELAY
3.INSPECT IGR NO. 3 RELAY

OK

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGR NO. 3 RELAY)

NG

REPLACE IGR NO. 3 RELAY

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGR NO. 3 RELAY)
a.
A485542C01
0.125,0.125 0.438,0.281 0.313,0.156 10 false *1 2.052,0.26 2.365,0.417 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 IGR NO. 3 Relay


Remove the IGR NO. 3 relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (IGR NO. 3 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IGR NO. 3 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGR NO. 3 RELAY)

5.CHECK HARNESS AND CONNECTOR (IGR NO. 3 RELAY - BODY GROUND)
a.

Remove the IGR NO. 3 relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGR NO. 3 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (IGR NO. 3 RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IGR NO. 3 RELAY - ECM)
a.

Remove the IGR NO. 3 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

5 (IGR NO. 3 relay) - B1-7 (IGR) Always Below 1 Ω
5 (IGR NO. 3 relay) or B1-7 (IGR) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR