This DTC is output when an open circuit or short occurs in the communication line between a front corner ultrasonic sensor (FL sensor) and the front center ultrasonic sensor (FLC sensor), or when a malfunction occurs in a front corner ultrasonic sensor (FL sensor) on the front.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C1AE187 | Ultrasonic Sensor (Front Left Corner) Missing Message | Front corner ultrasonic sensor (FL sensor) lost communication |
·
Front corner ultrasonic sensor (FL sensor)
·
Harness or connector
·
Clearance warning ECU assembly |
Clearance Warning | B |
Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>CALIBRATION
If a DTC is detected again after the repair, turn the ignition switch to ON and turn the TOYOTA parking assist-sensor system on, and then clear the DTC.
If C1AE296 is output at the same time, check C1AE296 first.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE296
Check the vehicle condition and work details.
| Result | Proceed to |
|---|---|
| The clearance warning ECU assembly or ultrasonic sensor has not been replaced | A |
| The clearance warning ECU assembly or ultrasonic sensor has been replaced | B |
A
B
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION
Check that the connector is properly connected to the front corner ultrasonic sensor and front center ultrasonic sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| C1AE187 is not output | A |
| C1AE187 is output | B |
A
B
Check that the connector is properly connected to the clearance warning ECU assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| C1AE187, C1AE287, C1AE387 and C1AE487 are output | B |
| C1AE187, C1AE287 and C1AE387 are output | C |
| C1AE187 and C1AE287 are output | D |
| C1AE187 is output | E |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE487
C
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE387
D
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE287
E
Pre-procedure1
Disconnect the A5 front center ultrasonic sensor (FLC sensor) connector.
Disconnect the A6 front corner ultrasonic sensor (FL sensor) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(A5,A6)Location & Routingewd_type=routing;type=c,c;code=A5,A6 Click Connector(A5)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Front Ultrasonic Sensor Center LHewd_type=component;type=c;code=A5;pinno=1,2,3 Click Connector(A6)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Front Ultrasonic Sensor Corner LHewd_type=component;type=c;code=A6;pinno=4,5,6 |
||
| A5-1 (BO) - A6-4 (BI) | Always | Below 1 Ω |
| A5-2 (SO) - A6-5 (SI) | Always | Below 1 Ω |
| A5-3 (EO) - A6-6 (EI) | Always | Below 1 Ω |
| A5-1 (BO) or A6-4 (BI) - Body ground | Always | 10 kΩ or higher |
| A5-2 (SO) or A6-5 (SI) - Body ground | Always | 10 kΩ or higher |
| A5-3 (EO) or A6-6 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the front corner ultrasonic sensor (FL sensor) with a known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| C1AE187 is not output | A |
| C1AE187 is output | B |
A
B