Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › CLEARANCE WARNING ECU
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0467775 CLEARANCE WARNING ECU A

PARK ASSIST / MONITORING  CLEARANCE WARNING ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B594935N01
0.292,0.25 4.5,2.167 4.208,1.917 2.417,2.167 2.417,0.25 false 5.5,1.438 5.833,1.438 5.833,1.438 6.083,1.688 false 3.417,1.198 3.25,1.031 3.25,1.031 3.083,1.031 false 1.24,1.208 1.073,1.042 1.073,1.042 0.906,1.042 false 0.708,0.875 0.99,1.229 0.281,0.354 18 false 2 5.333,1.26 5.615,1.615 0.281,0.354 18 false 1 2.875,0.875 3.156,1.229 0.281,0.354 18 false 3 1.802,0.896 2.26,1.094 0.458,0.198 10 false x 2 0.385,0.323 0.844,0.521 0.458,0.198 12 false *A 2.5,0.323 2.958,0.521 0.458,0.198 12 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

1 LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY 55320 - - -
2 ECU INTEGRATION BOX RH 82877 (Click here) - -
3 ECU INTEGRATION BOX LH 82878 (Click here) - -

*A for LHD *B for RHD

B620522N01
0.5,0.333 6.75,2.583 6.25,2.25 3.667,2.583 3.667,0.333 false 2.323,1.958 2.427,1.698 2.427,1.698 2.625,1.698 false 5.604,1.938 5.771,1.698 5.771,1.698 5.969,1.698 false 0.625,0.417 1,0.656 0.375,0.24 12 false *A 3.792,0.417 4.167,0.656 0.375,0.24 12 false *B 2.885,1.531 3.167,1.885 0.281,0.354 18 false 4 6.24,1.531 6.521,1.885 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

4 CLEARANCE WARNING ECU ASSEMBLY 89340A (Click here) - -

*A for LHD *B for RHD

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the clearance warning ECU assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Clearance warning ECU assembly Update ECU security key Vehicle control history (RoB) are stored (Click here)
w/ Parking Support Brake System:
·

Ultrasonic sensor detection angle

·

Steering angle neutral point

·

Bumper type registration

·

Ultrasonic sensor detection angle registration


·

TOYOTA parking assist-sensor system

·

Parking support brake system


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



·

Use the same procedure for RHD and LHD vehicles.



PROCEDURE

Hide 55320 1.REMOVE LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY

Hide 82877 2.REMOVE ECU INTEGRATION BOX RH (for LHD)

Z101186

Click here(Click here)

Hide 82878 3.REMOVE ECU INTEGRATION BOX LH (for RHD)

Z101186

Click here(Click here)

Hide 89340A 4.REMOVE CLEARANCE WARNING ECU ASSEMBLY

Z101186

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.




a.
B594936C01
1.969,0.094 2.344,0.333 0.375,0.24 12 false *A 5.323,0.115 5.698,0.354 0.375,0.24 12 false *B
*A for LHD *B for RHD
V113147

Remove in this Direction - -