| *A | for Standard | *B | for Aero Type |
| *C | w/ Garnish | *D | w/o Garnish |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 11 | ULTRASONIC SENSOR CUSHION SET | 89305 | ( ) |
- | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the ultrasonic sensor (for Front) removal/installation are shown below.
1.REMOVE FRONT BUMPER ASSEMBLY
for Standard:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Standard)>REMOVAL
for Aero Type:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Aero Type)>REMOVAL
52410B 2.REMOVE FRONT BUMPER GUARD ASSEMBLY (w/ Garnish)
89341K 3.REMOVE FRONT CORNER ULTRASONIC SENSOR
| *A | for Standard | *B | for Aero Type |
The orientation for the RH side is the opposite of the LH side.
89341L 4.REMOVE FRONT CENTER ULTRASONIC SENSOR
| *A | for Standard | *B | for Aero Type |
| *C | w/ Garnish | - | - |
The orientation for the RH side is the opposite of the LH side.
89C48D 5.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER
|
|
| Part | Temperature |
|---|---|
| Front Bumper Assembly | 40 to 60 °C (104 to 140 °F) |
| Front Corner Ultrasonic Sensor Retainer | 40 to 60 °C (104 to 140 °F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front bumper assembly and front corner ultrasonic sensor retainer excessively.
Heat the adhesive of the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.
Remove the front corner ultrasonic sensor retainer.
The orientation for the RH side is the opposite of the LH side.
53113C 6.REMOVE LOWER RADIATOR GRILLE LH (for Standard, w/o Garnish)
53112C 7.REMOVE LOWER RADIATOR GRILLE RH (for Standard, w/o Garnish)
Use the same procedure described for LH side.
89C48E 8.REMOVE FRONT CENTER ULTRASONIC SENSOR RETAINER (for Standard, w/o Garnish)
|
|
| Part | Temperature |
|---|---|
| Front Bumper Assembly | 40 to 60 °C (104 to 140 °F) |
| Front Center Ultrasonic Sensor Retainer | 40 to 60 °C (104 to 140 °F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front bumper assembly and front center ultrasonic sensor retainer excessively.
Heat the adhesive of the front bumper assembly and front center ultrasonic sensor retainer using a heat light.
Remove the front center ultrasonic sensor retainer.
The orientation for the RH side is the opposite of the LH side.
53142G 9.REMOVE NO. 2 RADIATOR GRILLE GARNISH (for Aero Type)
|
|
53141B 10.REMOVE NO. 1 RADIATOR GRILLE GARNISH (for Aero Type)
Use the same procedure described for the No. 2 radiator grille garnish.
89305 11.REMOVE ULTRASONIC SENSOR CUSHION SET
|
|
|
Remove in this Direction | - | - |