The rear air mix damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air mix damper to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the output air. The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the No. 1 cooler wiring harness sub-assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| B144F7F | Rear Left Air Mix Damper Control Servo Motor Actuator Stuck Off | Diagnosis Condition: During rear air mix damper servo sub-assembly operation Malfunction Status: Error or lost communication with rear air mix damper servo sub-assembly Detection Time: Continuously for 10 seconds or more |
·
Rear air mix damper servo sub-assembly
·
No. 2 cooler wiring harness sub-assembly
·
Air conditioning blower assembly
·
Air conditioning amplifier assembly |
Memorized | Air Conditioner | A |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Rear air mix damper servo sub-assembly operating | ○ | ○ |
| Malfunction Status | Damper servo operation request signals are output but the damper position sensor value does not change | ○ | - |
| Damper servo operation request signals are output but the damper position sensor value is abnormal | - | ○ | |
| Detection Time | Continuously for 30 seconds or more | Continuously for 30 seconds or more | |
| Trip Count | 1 trip | 1 trip | |
If the conditions of either of these patterns are detected, a DTC will be stored.
This DTC is also output for the damper link, damper lock, etc. Before performing inspection, perform servomotor initialization and check that there are no mechanical malfunctions.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>INITIALIZATION
This DTC is also output when servomotor initialization has failed. When servomotor initialization has failed, repair any malfunctions and perform servomotor initialization again.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>INITIALIZATION
Check that the rear air mix damper servo sub-assembly is installed correctly.
The rear air mix damper servo sub-assembly is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for a wire harness caught between the links of the motors and dampers.
No wire harnesses are caught between the links of the motors and dampers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform the following Active Test and read the Data List value.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Left Air Mix Damper Control Servo Motor | Rear air mix damper servo sub-assembly operation | Min: 128 Max: 384 |
Operates between 254 to 299 |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Left Air Mix Damper Control Servo Motor Actual Pulse | Rear air mix damper servo sub-assembly actual pulse | 128 to 384 |
·
MAX COLD: 254 (pulse)
·
MAX HOT: 299 (pulse) |
- |
| Active Test Display |
|---|
| Rear Left Air Mix Damper Control Servo Motor |
| Data List Display |
|---|
| Rear Left Air Mix Damper Control Servo Motor Actual Pulse |
The value of the Data List changes in accordance with the operation of the Active Test.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform the following Active Test and read the Data List value.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Left Air Mix Damper Control Servo Motor | Rear air mix damper servo sub-assembly operation | Min: 128 Max: 384 |
Operates between 254 to 299 |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Left Air Mix Damper Control Servo Motor Target Pulse | Rear air mix damper servo sub-assembly target pulse | 128 to 384 |
·
MAX COLD: 254 (pulse)
·
MAX HOT: 299 (pulse) |
- |
| Rear Left Air Mix Damper Control Servo Motor Actual Pulse | Rear air mix damper servo sub-assembly actual pulse | 128 to 384 |
·
MAX COLD: 254 (pulse)
·
MAX HOT: 299 (pulse) |
- |
| Active Test Display |
|---|
| Rear Left Air Mix Damper Control Servo Motor |
| Data List Display |
|---|
| Rear Left Air Mix Damper Control Servo Motor Target Pulse |
| Rear Left Air Mix Damper Control Servo Motor Actual Pulse |
The target pulse value of the Data List matches the actual pulse.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform the following Active Test and read the Data List value.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Left Air Mix Damper Control Servo Motor | Rear air mix damper servo sub-assembly operation | Min: 128 Max: 384 |
Operates between 254 to 299 |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Left Air Mix Damper Control Servo Motor Actual Pulse | Rear air mix damper servo sub-assembly actual pulse | 128 to 384 |
·
MAX COLD: 254 (pulse)
·
MAX HOT: 299 (pulse) |
- |
| Active Test Display |
|---|
| Rear Left Air Mix Damper Control Servo Motor |
| Data List Display |
|---|
| Rear Left Air Mix Damper Control Servo Motor Actual Pulse |
The value of the Data List changes in accordance with the operation of the Active Test.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform the following Active Test and read the Data List value.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Right Air Mix Damper Control Servo Motor | No. 2 rear air mix damper servo sub-assembly operation | Min: 128 Max: 384 |
Operates between 213 to 258 |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Right Air Mix Damper Control Servo Motor Actual Pulse | No. 2 rear air mix damper servo sub-assembly actual pulse | 128 to 384 |
·
MAX COLD: 258 (pulse)
·
MAX HOT: 213 (pulse) |
- |
| Active Test Display |
|---|
| Rear Right Air Mix Damper Control Servo Motor |
| Data List Display |
|---|
| Rear Right Air Mix Damper Control Servo Motor Actual Pulse |
The value of the Data List changes in accordance with the operation of the Active Test.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the rear air mix damper servo sub-assembly.
Procedure1
Operate the dampers by hand.
The dampers are easily operated by hand.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG