Home › Engine / Hybrid System › V35A-FTS (STARTING) › STARTER (w/ Stop And Start System)
RM38G0E _51 Engine / Hybrid System _101526 V35A-FTS STARTING _0470473 STARTER(w/ Stop And Start System) A

V35A-FTS STARTING  STARTER(w/ Stop And Start System)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A488748N03
0.823,0.344 0.99,0.344 0.99,0.344 1.156,0.677 true 3.156,3.469 3.417,3.094 3.417,3.094 3.677,3.094 true 4.146,4.198 4.146,4.531 4.146,4.531 4.5,4.531 true 2.75,3.833 2.917,3.833 2.917,3.833 3.083,4.167 true 1.208,4.406 1.208,4.625 1.208,4.625 1.458,4.625 true 6.438,0.219 6.854,0.219 true 6.417,0.615 6.833,0.615 true 2.052,1.594 2.302,1.594 2.302,1.594 2.313,1.917 true 0.615,1.5 0.948,1.5 0.948,1.5 0.948,1.917 true 0.635,0.198 0.938,0.469 0.302,0.271 18 false 3 3.74,2.969 4.052,3.24 0.313,0.271 18 false 7 4.844,4.427 5.208,4.688 0.365,0.26 18 false 8 2.552,3.708 2.802,4.042 0.25,0.333 18 false 9 5.313,3.854 5.625,4.052 0.313,0.198 10 false x 2 6.167,0.073 6.406,0.344 0.24,0.271 18 true 1 6.188,0.49 6.427,0.75 0.24,0.26 18 true 2 1.51,4.469 1.823,4.729 0.313,0.26 18 false 6 0.396,1.375 0.698,1.635 0.302,0.26 18 false 4 1.844,1.438 2.125,1.698 0.281,0.26 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 CONVERTER WITH CATALYST ASSEMBLY RH 17400M - - -
4 AIR CLEANER CAP WITH AIR CLEANER HOSE 17735 - - -
5 NO. 1 ENGINE COVER SUB-ASSEMBLY 12601F - - -
6 ENGINE WIRE 82121 - - -
7 STARTER COVER 28192 - - -
8 STARTER ASSEMBLY 28100 (Click here) - -
9 STARTER TERMINAL 28181 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the starter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 2)

·

Gas leaks from exhaust system


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Starter assembly
NOTICE:

When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.


Clear number of starter operations Stop and start system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)

·

When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.




Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 17400M 3.REMOVE CONVERTER WITH CATALYST ASSEMBLY RH

Hide 17735 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 12601F 5.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 82121 6.DISCONNECT ENGINE WIRE

a.
A489717


Hide 28192 7.REMOVE STARTER COVER

a.
A488744


Hide 28100 8.REMOVE STARTER ASSEMBLY

a.
Z101186

NOTICE:

When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.



A488745


Hide 28181 9.REMOVE STARTER TERMINAL

a.
A488747