Home › Engine / Hybrid System › V35A-FTS (EMISSION CONTROL) › MONOLITHIC CONVERTER
RM38G0E _51 Engine / Hybrid System _101527 V35A-FTS EMISSION CONTROL _0470485 MONOLITHIC CONVERTER A

V35A-FTS EMISSION CONTROL  MONOLITHIC CONVERTER  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A478010N01
5.948,1.271 6.719,1.458 0.771,0.188 2.396,0.844 3.167,1.031 0.771,0.188 2.052,0.073 2.823,0.26 0.771,0.188 2.5,3.156 3.271,3.344 0.771,0.188 4.083,2.125 4.854,2.313 0.771,0.188 6.094,1.969 6.865,2.156 0.771,0.188 3.833,0.542 4.604,0.729 0.771,0.188 6.156,2.875 6.927,3.063 0.771,0.188 2.833,0.417 3,0.417 3,0.417 3.417,0.5 true 4.427,0.427 4.76,0.208 4.76,0.208 4.927,0.208 true 5.292,1.979 5.625,1.76 5.625,1.76 5.792,1.76 true 2.833,0.167 3,0.167 false 4.865,2.219 5.125,2.219 false 3.167,0.938 3.333,0.938 false 3.448,2.823 3.448,3.24 3.448,3.24 3.281,3.24 false 5.458,0.625 5.792,0.156 5.792,0.156 5.958,0.156 true 6.177,2.698 6.333,2.417 6.333,2.417 6.5,2.417 true 3.313,1.24 3.479,1.24 3.479,1.24 3.865,0.99 true 4.313,1.76 4.479,1.76 4.479,1.76 4.635,1.479 true 3.604,3.49 3.771,3.49 3.771,3.49 4.208,2.927 true 4.875,3.417 5.042,3.417 5.042,3.417 5.229,3.302 true 5.677,1.104 5.927,0.635 5.927,0.635 6.094,0.635 true 6.594,3.375 6.698,3.635 6.698,3.635 6.865,3.635 true 4.75,2.688 4.917,2.688 4.917,2.688 5.104,2.51 true 6.292,1.26 6.292,0.844 false 7.031,3.083 7.031,2.042 7.031,2.042 6.865,2.042 false 4.771,0.854 4.771,0.635 4.771,0.635 4.604,0.635 false 5.979,3.094 5.979,2.969 5.979,2.969 6.146,2.969 false 4.104,1.615 4.354,1.948 0.25,0.333 18 false 1 4.625,3.313 4.875,3.646 0.25,0.333 18 false 2 4.573,2.573 4.823,2.906 0.25,0.333 18 false 4 2.646,0.302 2.896,0.635 0.25,0.333 18 false 3 5.031,0.104 5.281,0.438 0.25,0.333 18 false 5 5.854,1.646 6.104,1.979 0.25,0.333 18 false 5 2.406,1.042 3.021,1.24 0.615,0.198 10 false ● *3 3.271,3.406 3.885,3.604 0.615,0.198 10 false ● *2 2.51,3.375 3.125,3.573 0.615,0.198 10 false ● *1 3.01,1.167 3.625,1.365 0.615,0.198 10 false ● *4 3.135,0.052 3.594,0.25 0.458,0.198 10 false x 2 5.292,2.115 5.75,2.313 0.458,0.198 10 false x 2 2.146,0.094 3.5,0.25 1.354,0.156 8 false 10 (102, 7) 2.479,0.865 3.833,1.021 1.354,0.156 8 false 25 (255, 18) 2.583,3.177 3.938,3.333 1.354,0.156 8 false 25 (255, 18) 6.021,0.052 6.271,0.385 0.25,0.333 18 false 5 6.573,2.313 6.823,2.646 0.25,0.333 18 false 5 6.365,0.719 6.823,0.917 0.458,0.198 10 false x 2 6.021,0.948 6.271,1.146 0.25,0.198 10 false x 2 6.906,3.177 7.156,3.375 0.25,0.198 10 false x 2 6.635,3.208 6.885,3.406 0.25,0.198 10 false x 2 4.188,2.146 5.542,2.302 1.354,0.156 8 false 10 (102, 7) 6.167,0.542 6.781,0.74 0.615,0.198 10 false ● 6.948,3.542 7.135,3.729 0.188,0.188 10 false ● 6.01,1.292 6.781,1.479 0.771,0.188 8 false 43 (438, 32) 6.156,2 6.927,2.188 0.771,0.188 8 false 43 (438, 32) 3.906,0.573 4.677,0.76 0.771,0.188 8 false 43 (438, 32) 6.219,2.906 6.99,3.094 0.771,0.188 8 false 43 (438, 32)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CONVERTER WITH CATALYST ASSEMBLY RH 17400M (Click here) - -
2 CONVERTER WITH CATALYST ASSEMBLY LH 17500 (Click here) - -
3 NO. 2 TURBO INSULATOR 17272 - - -
4 NO. 4 TURBO INSULATOR 1728A - - -
5 AIR FUEL RATIO SENSOR - - - -

*1 EXHAUST PIPE CLAMP LH *2 TURBINE OUTLET ELBOW GASKET LH
*3 EXHAUST PIPE CLAMP RH *4 TURBINE OUTLET ELBOW GASKET RH
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

PROCEDURE

Hide 17400M 1.INSTALL CONVERTER WITH CATALYST ASSEMBLY RH

a.
A483487C01
4.479,1.5 4.688,1.5 4.688,1.5 5.104,1.281 true 5.458,0.74 5.906,0.74 true 4.292,1.427 4.604,1.625 0.313,0.198 10 false *1 5.979,0.656 6.292,0.854 0.313,0.198 10 false *a 0.458,0.083 1.25,0.406 0.792,0.323 18 false i, ii
*1 Gasket - -
*a Wooden Block - -


i.

Temporarily install a new gasket to the converter with catalyst assembly RH.


ii.

Using a plastic-faced hammer and wooden block, tap in the gasket until its surface is flush with the converter with catalyst assembly RH.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.





b.
A477998C01
5.333,1.5 5.167,1.5 5.167,1.5 5,1.083 true 4.865,1.125 4.583,1.406 4.583,1.406 4.417,1.406 true 1.208,1.083 1.031,0.875 1.031,0.875 0.865,0.875 true 1.302,1.469 1.115,1.854 1.115,1.854 0.948,1.854 true 2.844,0.271 2.677,0.271 2.677,0.271 2.323,0.771 true 2.917,0.563 2.75,0.563 2.75,0.563 1.979,1.146 true 0.406,0.146 0.688,0.5 0.281,0.354 18 false i 4.063,2.063 4.573,2.438 0.51,0.375 18 true ii, iv 2.302,4.031 2.594,4.302 0.292,0.271 18 true iii 4.469,0.271 4.719,0.604 0.25,0.333 18 true v 2.281,4.344 3,4.635 0.719,0.292 18 true vii, viii 4.073,2.417 4.417,2.75 0.344,0.333 18 true vi 5.417,1.417 5.583,1.583 0.167,0.167 10 true *c 4.25,1.333 4.417,1.5 0.167,0.167 10 true *d 5.417,0.833 5.583,1 0.167,0.167 10 true *e 0.677,0.792 0.844,0.958 0.167,0.167 10 true *1 0.771,1.792 0.938,1.958 0.167,0.167 10 true *2 2.927,0.198 3.094,0.365 0.167,0.167 10 true *b 2.969,0.49 3.135,0.656 0.167,0.167 10 true *b 1.385,0.594 1.552,0.76 0.167,0.167 10 true *a
*1 Converter With Catalyst Assembly RH *2 Turbine Outlet Elbow Gasket RH
*a 1.5 mm (0.0590 in.) or less *b Knock Pin
*c Alignment Protrusion on Exhaust Pipe Clamp Side RH *d Alignment Protrusion on Converter With Catalyst Assembly RH Side
*e Position Alignment Range - -


i.

Install a new turbine outlet elbow gasket RH to the converter with catalyst assembly RH as shown in the illustration.

NOTICE:
·

When reusing the converter with catalyst assembly RH, thoroughly clean the gasket groove so that no old gasket remains.

·

Fully insert the gasket into the gasket groove of the converter with catalyst assembly RH.




ii.

Set a new exhaust pipe clamp RH to the converter with catalyst assembly RH.

NOTICE:

Make sure the end of the exhaust pipe clamp RH does not open 140 mm (5.51 in.) or more (standard amount approximately 60 mm (2.36 in.)).



iii.

Temporarily install the converter with catalyst assembly RH to the manifold stay with the nut.

NOTICE:

Tighten the nut by hand until it contacts the surface.



iv.

Align the converter with catalyst assembly RH with the knock hole on the No. 2 turbocharger sub-assembly side to connect the converter with catalyst assembly RH.

NOTICE:

Make sure that there is a knock pin on the converter with catalyst assembly RH.



v.

Align the flange surfaces of the No. 2 turbocharger sub-assembly and converter with catalyst assembly RH, and then temporarily install the exhaust pipe clamp RH.

NOTICE:

Align the position alignment protrusions on the exhaust pipe clamp RH side to within the range of the position alignment protrusions on the converter with catalyst assembly RH side.



vi.

Tighten the exhaust pipe clamp RH.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


vii.

Tighten the nut.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


viii.

Connect the converter with catalyst assembly RH to the front exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)



Hide 17500 2.INSTALL CONVERTER WITH CATALYST ASSEMBLY LH

a.
A483487C01
4.479,1.5 4.688,1.5 4.688,1.5 5.104,1.281 true 5.458,0.74 5.906,0.74 true 4.292,1.427 4.604,1.625 0.313,0.198 10 false *1 5.979,0.656 6.292,0.854 0.313,0.198 10 false *a 0.458,0.083 1.25,0.406 0.792,0.323 18 false i, ii
*1 Gasket - -
*a Wooden Block - -


i.

Temporarily install a new gasket to the converter with catalyst assembly LH.


ii.

Using a plastic-faced hammer and wooden block, tap in the gasket until its surface is flush with the converter with catalyst assembly LH.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.





b.
A477999C01
5.5,1.75 5.333,1.75 5.333,1.75 5.083,1.083 true 5.583,1.417 5.417,1.417 5.417,1.417 5.25,1.167 true 3.083,1.167 3,1.167 3,1.167 2.75,1.333 true 2.917,2.083 2.833,2.083 2.833,2.083 2.667,1.667 true 1.781,1 1.417,0.333 1.417,0.333 1.333,0.333 true 2.01,1.51 1.25,0.583 1.25,0.583 1.167,0.583 true 0.458,0.188 0.625,0.438 0.167,0.25 18 false i 4,2.083 4.5,2.333 0.5,0.25 18 true ii, iv 4,2.333 4.25,2.583 0.25,0.25 18 true vi 4.49,0.271 4.656,0.521 0.167,0.25 18 true v 2.594,3.896 2.76,4.146 0.167,0.25 18 true iii 2.573,4.167 3.323,4.417 0.75,0.25 18 true vii, viii 4.583,0.667 4.75,0.833 0.167,0.167 10 true *e 5.5,1.667 5.667,1.833 0.167,0.167 10 true *c 5.583,1.333 5.75,1.5 0.167,0.167 10 true *d 2.75,0.833 2.917,1 0.167,0.167 10 false *a 3.167,1.083 3.333,1.25 0.167,0.167 10 false *1 3,2 3.167,2.167 0.167,0.167 10 false *2 1.083,0.25 1.25,0.417 0.167,0.167 10 false *b 0.917,0.5 1.083,0.667 0.167,0.167 10 false *b
*1 Converter With Catalyst Assembly LH *2 Turbine Outlet Elbow Gasket LH
*a 1.5 mm (0.0590 in.) or less *b Knock Pin
*c Alignment Protrusion on Exhaust Pipe Clamp Side LH *d Alignment Protrusion on Converter With Catalyst Assembly LH Side
*e Position Alignment Range - -


i.

Install a new turbine outlet elbow gasket LH to the converter with catalyst assembly LH as shown in the illustration.

NOTICE:
·

When reusing the converter with catalyst assembly LH, thoroughly clean the gasket groove so that no old gasket remains.

·

Fully insert the gasket into the gasket groove of the converter with catalyst assembly LH.




ii.

Set a new exhaust pipe clamp LH to the converter with catalyst assembly LH.

NOTICE:

Make sure the end of the exhaust pipe clamp LH does not open 140 mm (5.51 in.) or more (standard amount approximately 60 mm (2.36 in.)).



iii.

Temporarily install the converter with catalyst assembly LH to the manifold stay with the nut.

NOTICE:

Tighten the nut by hand until it contacts the surface.



iv.

Align the converter with catalyst assembly LH with the knock hole on the No. 1 turbocharger sub-assembly side to connect the converter with catalyst assembly LH.

NOTICE:

Make sure that there is a knock pin on the converter with catalyst assembly LH.



v.

Align the flange surfaces of the No. 1 turbocharger sub-assembly and converter with catalyst assembly LH, and then temporarily install the exhaust pipe clamp LH.

NOTICE:

Align the position alignment protrusions on the exhaust pipe clamp LH side to within the range of the position alignment protrusions on the converter with catalyst assembly LH side.



vi.

Tighten the exhaust pipe clamp LH.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


vii.

Tighten the nut.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


viii.

Connect the converter with catalyst assembly LH to the center exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)



Hide 17272 3.INSTALL NO. 2 TURBO INSULATOR

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Hide 1728A 4.INSTALL NO. 4 TURBO INSULATOR

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)