Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469675 MULTI-TERRAIN MONITOR SYSTEM Y

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the multi-terrain monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
a.

Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.

HINT:

The multi-terrain monitor display may be temporarily distorted due to radio waves around the vehicle.

Problem Symptom Cause
The problem symptom indicates a multi-terrain monitor display malfunction and the problem symptom cannot be reproduced. The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver.



Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding.


Result:
Proceed to
NEXT



NEXT

4.CHECK NAVIGATION SYSTEM OR AUDIO AND VISUAL SYSTEM
4.CHECK NAVIGATION SYSTEM OR AUDIO AND VISUAL SYSTEM
a.


Result:
Result Proceed to
Navigation system and audio and visual system are normal A
Navigation system is abnormal B
Audio and visual system is abnormal C



A

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

B

C

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

6.CHECK FOR DTC*

B

6.CHECK FOR DTC*
a.

Check for DTCs and note any codes that are output.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 470
Chassis > Rear Camera > Trouble Codes
50001 85

b.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 470
Chassis > Rear Camera > Trouble Codes
50001 85

c.

Recheck for DTCs. Try to reproduce the problem symptoms based on the recorded DTCs, and then check if the DTCs are output again.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 470
Chassis > Rear Camera > Trouble Codes
50001 85
NOTICE:

The parking assist ECU outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the multi-terrain monitor system are output, refer to Diagnostic Trouble Code Chart for the relevant systems.

System Proceed to
Panoramic View Monitor System (Click here)



Result:
Result Proceed to
DTC is not output A
DTC is output B



A

7.CHECK FOR VEHICLE CONTROL HISTORY*

B

7.CHECK FOR VEHICLE CONTROL HISTORY*
HINT:

Refer to Vehicle Control History.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>VEHICLE CONTROL HISTORY (RoB)


a.

Check for vehicle control history and note any codes that are output.

Chassis > Circumference Monitoring Camera Control Module > Utility
Tester Display
Vehicle Control History (RoB)
50005 470 55

Result:
Result Proceed to
No vehicle control history is output A
Vehicle control history is output B



A

8.PROBLEM SYMPTOMS TABLE

B

8.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

9.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

10.ADJUST, REPAIR OR REPLACE
9.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

10.ADJUST, REPAIR OR REPLACE
10.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

11.CONFIRMATION TEST
11.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END