This DTC is stored if the parking assist ECU determines that the input/output signal communication with the rear television camera assembly is abnormal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C1621 | Back Camera Power Supply Failure | Rear television camera assembly power supply malfunction |
·
Harness or connector
·
Rear television camera assembly
·
Parking assist ECU |
Rear Camera | A |
When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION
Pre-procedure1
Disconnect the I131 parking assist ECU connector.
Disconnect the g18 rear television camera assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I131,g18)Location & Routingewd_type=routing;type=c,c;code=I131,g18 Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assemblyewd_type=component;type=c;code=g18;pinno=4,3 |
||
| I131-2 (CB+) - g18-4 (CB+) | Always | Below 1 Ω |
| I131-1 (CGND) - g18-3 (CGND) | Always | Below 1 Ω |
| I131-2 (CB+) or g18-4 (CB+) - Body ground | Always | 10 kΩ or higher |
| I131-1 (CGND) or g18-3 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the g18 rear television camera assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(g18)Location & Routingewd_type=routing;type=c;code=g18 Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assemblyewd_type=component;type=c;code=g18;pinno=3 |
||
| g18-3 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(g18)Location & Routingewd_type=routing;type=c;code=g18 Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assemblyewd_type=component;type=c;code=g18;pinno=4 |
||
| g18-4 (CB+) - Body ground | Ignition switch ON | 7 to 8 V |
| Ignition switch off | Below 1 V | |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
for LHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for LHD)>REMOVAL
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU (for RHD)>REMOVAL