Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469676 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C162287  Rear Camera Image Signal Missing Message  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the rear television camera assembly are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C162287 Rear Camera Image Signal Missing Message Open or short in the rear television camera signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Parking assist ECU


Circumference Monitoring Camera Control Module A

WIRING DIAGRAM

E431809E12
5.552,3.052 6.823,3.271 1.271,0.219 10 false Parking Assist ECU 5.542,2.896 5.958,3.073 0.417,0.177 10 false I131 5.521,0.573 5.875,0.771 0.354,0.198 10 false CB+ 5.521,1.083 5.885,1.281 0.365,0.198 10 false CV+ 5.51,1.573 5.885,1.771 0.375,0.198 10 false CV- 5.292,0.51 5.729,0.708 0.438,0.198 10 false 2 5.292,1.479 5.438,1.688 0.146,0.208 10 false 3 5.51,2.01 6.042,2.219 0.531,0.208 10 false CGND 5.292,1.938 5.729,2.135 0.438,0.198 10 false 1 5.302,2.302 5.479,2.479 0.177,0.177 10 false 5 5.521,2.396 5.99,2.583 0.469,0.188 10 false SGND 0.448,2.875 0.74,3.063 0.292,0.188 10 false g18 0.427,3.052 2.573,3.302 2.146,0.25 10 false Rear Television Camera Assembly 1.292,0.594 1.667,0.781 0.375,0.188 10 false CB+ 1.292,1.094 1.646,1.271 0.354,0.177 10 false CV+ 1.313,1.573 1.635,1.771 0.323,0.198 10 false CV- 1.177,2.021 1.646,2.208 0.469,0.188 10 false CGND 1.688,0.99 1.896,1.156 0.208,0.167 10 false 6 1.698,0.51 1.896,0.698 0.198,0.188 10 false 4 1.708,1.917 2.146,2.115 0.438,0.198 10 false 3 1.708,2.313 1.865,2.5 0.156,0.188 10 false 7 3.521,2.365 3.677,2.563 0.156,0.198 10 false * 0.333,3.417 1.854,3.677 1.521,0.26 10 false *: Shielded 1.188,2.396 1.708,2.573 0.521,0.177 10 false SGND 1.698,1.49 1.906,1.677 0.208,0.188 10 false 5 5.302,0.979 5.74,1.177 0.438,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)

Pre-procedure1

a.

Disconnect the I131 parking assist ECU connector.


b.

Disconnect the g18 rear television camera assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I131,g18)Location & Routing

Click Connector(I131)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Parking Assist ECU

Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

I131-2 (CB+) - g18-4 (CB+) Always Below 1 Ω
I131-4 (CV+) - g18-6 (CV+) Always Below 1 Ω
I131-3 (CV-) - g18-5 (CV-) Always Below 1 Ω
I131-1 (CGND) - g18-3 (CGND) Always Below 1 Ω
I131-5 (SGND) - g18-7 (SGND) Always Below 1 Ω
I131-2 (CB+) or g18-4 (CB+) - Body ground Always 10 kΩ or higher
I131-4 (CV+) or g18-6 (CV+) - Body ground Always 10 kΩ or higher
I131-3 (CV-) or g18-5 (CV-) - Body ground Always 10 kΩ or higher
I131-1 (CGND) or g18-3 (CGND) - Body ground Always 10 kΩ or higher
I131-5 (SGND) or g18-7 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

2.CHECK PARKING ASSIST ECU (CV-, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (CV-, CGND)

Pre-procedure1

a.
E394295C01
1.979,0.854 2.333,0.479 2.333,0.479 2.583,0.479 true 2,1.104 2.354,1.563 2.354,1.563 2.604,1.563 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 2.646,0.417 3.167,0.615 0.521,0.198 10 false CGND 2.667,1.49 3.188,1.688 0.521,0.198 10 false CV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the I131 parking assist ECU connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (CGND) - Body ground Always Below 1 Ω
3 (CV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

3.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

3.CHECK PARKING ASSIST ECU (CB+, CGND)

Pre-procedure1

a.

Disconnect the g18 rear television camera assembly.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g18)Location & Routing

Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

g18-3 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(g18)Location & Routing

Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

g18-4 (CB+) - g18-3 (CGND) Ignition switch ON 7 to 8 V
g18-4 (CB+) - g18-3 (CGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG