Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469676 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C168187  Front Camera Image Signal Missing Message  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C168187 Front Camera Image Signal Missing Message Front television camera power supply failure
·

Harness or connector

·

Front television camera assembly

·

Parking assist ECU


Circumference Monitoring Camera Control Module A

WIRING DIAGRAM

E431809E13
5.542,3.021 6.813,3.25 1.271,0.229 10 false Parking Assist ECU 5.531,2.875 5.938,3.052 0.406,0.177 10 false I128 5.51,0.583 5.969,0.781 0.458,0.198 10 false BCB+ 5.521,1.073 5.979,1.271 0.458,0.198 10 false BCV+ 5.51,1.573 5.969,1.771 0.458,0.198 10 false BCV- 5.292,0.51 5.729,0.708 0.438,0.198 10 false 2 5.281,1.479 5.719,1.677 0.438,0.198 10 false 3 5.521,2 6.156,2.208 0.635,0.208 10 false BGND 5.292,1.938 5.729,2.135 0.438,0.198 10 false 1 5.302,2.302 5.74,2.5 0.438,0.198 10 false 5 5.51,2.385 6.146,2.594 0.635,0.208 10 false SGND 0.469,2.875 0.771,3.063 0.302,0.188 10 false A11 0.469,3.031 2.688,3.26 2.219,0.229 10 false Front Television Camera Assembly 1.208,0.594 1.667,0.792 0.458,0.198 10 false BCB+ 1.208,1.083 1.667,1.281 0.458,0.198 10 false BCV+ 1.229,1.563 1.688,1.76 0.458,0.198 10 false BCV- 1.188,2.042 1.656,2.229 0.469,0.188 10 false BGND 1.708,0.521 2.146,0.719 0.438,0.198 10 false 2 1.719,1.01 2.156,1.208 0.438,0.198 10 false 4 1.729,1.49 2.167,1.688 0.438,0.198 10 false 3 1.729,1.938 2.167,2.135 0.438,0.198 10 false 1 3.521,2.313 3.677,2.51 0.156,0.198 10 false * 0.333,3.417 1.854,3.677 1.521,0.26 10 false *: Shielded 1.188,2.438 1.823,2.646 0.635,0.208 10 false SGND 1.74,2.302 2.177,2.5 0.438,0.198 10 false 5 5.302,0.979 5.74,1.177 0.438,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)

Pre-procedure1

a.

Disconnect the I128 parking assist ECU connector.


b.

Disconnect the A11 front television camera assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I128,A11)Location & Routing

Click Connector(I128)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Parking Assist ECU

Click Connector(A11)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Front Television Camera Assembly

I128-2 (BCB+) - A11-2 (BCB+) Always Below 1 Ω
I128-4 (BCV+) - A11-4 (BCV+) Always Below 1 Ω
I128-3 (BCV-) - A11-3 (BCV-) Always Below 1 Ω
I128-1 (BGND) - A11-1 (BGND) Always Below 1 Ω
I128-5 (SGND) - A11-5 (SGND) Always Below 1 Ω
I128-2 (BCB+) or A11-2 (BCB+) - Body ground Always 10 kΩ or higher
I128-4 (BCV+) or A11-4 (BCV+) - Body ground Always 10 kΩ or higher
I128-3 (BCV-) or A11-3 (BCV-) - Body ground Always 10 kΩ or higher
I128-1 (BGND) or A11-1 (BGND) - Body ground Always 10 kΩ or higher
I128-5 (SGND) or A11-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

2.CHECK PARKING ASSIST ECU (BCV-, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (BCV-, BGND)

Pre-procedure1

a.
E394296C01
1.969,0.854 2.313,0.417 2.313,0.417 2.563,0.417 true 1.979,1.083 2.313,1.552 2.313,1.552 2.563,1.552 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 2.615,0.344 3.229,0.542 0.615,0.198 10 false BGND 2.625,1.479 3.24,1.677 0.615,0.198 10 false BCV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the I128 parking assist ECU connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BGND) - Body ground Always Below 1 Ω
3 (BCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

3.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

3.CHECK PARKING ASSIST ECU (BCB+, BGND)

Pre-procedure1

a.

Disconnect the A11 front television camera assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A11)Location & Routing

Click Connector(A11)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Front Television Camera Assembly

A11-1 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A11)Location & Routing

Click Connector(A11)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Front Television Camera Assembly

A11-2 (BCB+) - A11-1 (BGND) Ignition switch ON 7 to 8 V
A11-2 (BCB+) - A11-1 (BGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG