Home › Power Source / Network › V35A-FTS (BATTERY / CHARGING) › CHARGING SYSTEM
RM38G0E _57 Power Source / Network _101530 V35A-FTS BATTERY / CHARGING _0470503 CHARGING SYSTEM C

V35A-FTS BATTERY / CHARGING  CHARGING SYSTEM  P162B87  Lost Communication with Battery Monitor Module Missing Message  


DESCRIPTION

The ECM and battery state sensor assembly each detect reception malfunctions. A battery state sensor assembly reception malfunction detected by the battery state sensor assembly is sent to the ECM via LIN communication. If there is a malfunction in either the ECM or battery state sensor assembly, the ECM determines that there is a LIN communication malfunction and outputs a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Note
P162B87 Lost Communication with Battery Monitor Module Missing Message Battery state sensor assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch ON
(1 trip detection logic)
·

Battery state sensor assembly

·

ECM

·

Wire harness or connector


Charge warning is not displayed SAE: P162B

WIRING DIAGRAM

Refer to the wiring diagram for the P062049.

Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>CHARGING SYSTEM>P062049

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION

OK

2.CHECK CHARGING SYSTEM

NG

INSTALL BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK CHARGING SYSTEM

OK

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY STATE SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE CHARGING SYSTEM

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY STATE SENSOR ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the battery state sensor assembly connector.


c.

Disconnect the generator assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(C38,B39)Location & Routing

Click Connector(C38)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(B39)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Battery State Sensor Assembly

C38-17 (LIN) - B39-2 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(C38,C53,B39)Location & Routing

Click Connector(C38)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C53)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Generator with Regulator Assembly

Click Connector(B39)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Battery State Sensor Assembly

C38-17 (LIN), C53-2 (LIN) or B39-2 (LIN) - Body ground Ignition switch off
(while LIN communication stopped)
10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.

Disconnect the battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B39)Location & Routing

Click Connector(B39)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Battery State Sensor Assembly

B39-3 (+B) - Body ground Always 11 to 14 V
B39-1 (RBAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CLEAR DTC
a.

Check for DTCs using the GTS, and then write them down.

Powertrain > Engine > Trouble Codes
50001 372

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.READ OUTPUT DTC
6.READ OUTPUT DTC
a.

Start the engine and wait 17 minutes or more.


b.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
Only P162B87 is output A
P161A87 and P162B87 are output B
DTCs are not output C



A

B

C