Based on signals from the accelerator position sensor and transmission revolution sensors (NT and SP2), the TCM controls the solenoid (SLT) valve using a predetermined current. As a result, the line pressure is adjusted to a pressure that is appropriate for the throttle angle and engine output. Based on the rotation speed signals from the transmission revolution sensors (NT and SP2), the TCM calculates the heat level of the friction material, and detects clutch slippage, etc.
| TCM Commanded Gear | Actual Gear during SLT Stuck ON Malfunction |
|---|---|
| 1st | 1st or Neutral |
| 2nd | 2nd or Neutral |
| 3rd | 3rd or Neutral |
| 4th | 4th or Neutral |
| 5th | 5th or Neutral |
| 6th | 6th or Neutral |
| 7th | 7th or Neutral |
| 8th | 8th or Neutral |
| 9th | 9th or Neutral |
| 10th | 10th or Neutral |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P27137F | Pressure Control Solenoid "D" Actuator Stuck Off | While driving with the shift lever in D, the transmission revolution sensor (NT) value exceeds the specified speed for each gear (2-trip detection logic). |
·
Solenoid (SL1) valve
·
Solenoid (SL2) valve
·
Solenoid (SL3) valve
·
Solenoid (SL4) valve
·
Solenoid (SL5) valve
·
Solenoid (SL6) valve
·
Solenoid (SC1) valve
·
Solenoid (SL) valve
·
Solenoid (SR) valve
·
Solenoid (SLU) valve
·
Solenoid (SLT) valve
·
Transmission valve body assembly
·
Torque converter assembly
·
Automatic transmission assembly (clutch, brake, gear, etc.) |
Comes on | DTC stored | SAE: P2714 |
The TCM calculates the amount of heat absorbed by the friction material based on the difference in revolution speed (clutch slippage) between the turbine and output shaft. The TCM illuminates the MIL and stores this DTC when the amount of heat absorption exceeds the specified value.
When the solenoid (SLT) valve remains ON, oil pressure goes down and clutch engagement force decreases.
If driving continues under these conditions, the clutches will burn out and the vehicle will no longer be drivable.
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Perform the D Position Shift Test inspection in Road Test.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P27137F.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
| N/A |
·
Unable to perform DTC judgment
·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the automatic transmission are replaced.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC P27137F and DTC P07407E, P07457F, P076A71, P07707F, P07757F, P07957F, P08BA7F, P27567F, P28077F and/or P28167F are output | A |
| Only DTC P27137F is output | B |
| DTCs other than P07407E, P07457F, P076A71, P07707F, P07757F, P07957F, P08BA7F, P27137F, P27567F, P28077F and P28167F are also output | C |
If any DTCs other than P07407E, P07457F, P076A71, P07707F, P07757F, P07957F, P08BA7F, P27137F, P27567F, P28077F and P28167F are output, perform troubleshooting for those DTCs first.
A
B
C
Clear the DTCs.
Write down the currently output DTCs before clearing them.
Perform the stall speed test.
| Test Condition | Proceed to |
|---|---|
| Stall speed test can be performed | A |
| Stall speed test cannot be performed | B |
A
B
| *1 | Solenoid (SL1), (SL2), (SL3), (SL4), (SL5), (SL6) and (SLU) Valves |
Remove the solenoid (SL1), (SL2), (SL3), (SL4), (SL5), (SL6) and (SLU) valves.
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Solenoid (SL1) valve connector terminal 1 - terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
| Solenoid (SL2) valve connector terminal 1 - terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
| Solenoid (SL3) valve connector terminal 1 - terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
| Solenoid (SL4) valve connector terminal 1 - terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
| Solenoid (SL5) valve connector terminal 1 - terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
| Solenoid (SL6) valve connector terminal 1 - terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
| Solenoid (SLU) valve connector terminal 1 - terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.
Valve moves and makes an operating sound.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Solenoid (SC1) Valve |
Remove the solenoid (SC1) valve.
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal of solenoid (SC1) valve connector - Solenoid (SC1) valve body | 20°C (68°F) | 11 to 15 Ω |
Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.
Valve moves and makes an operating sound.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Solenoid (SL) and (SR) Valves |
Remove the solenoid (SL) and (SR) valves.
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal of solenoid (SL) valve connector - Solenoid (SL) valve body | 20°C (68°F) | 11 to 15 Ω |
| Terminal of solenoid (SR) valve connector - Solenoid (SR) valve body | 20°C (68°F) | 11 to 15 Ω |
Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.
Valve moves and makes an operating sound.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Solenoid (SLT) Valve |
Remove the solenoid (SLT) valve.
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.
Valve moves and makes an operating sound.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL
There is no foreign matter on each valve and they operate smoothly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION
The torque converter operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG