Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0472752 AUTOMATIC TRANSMISSION SYSTEM(for V35A-FTS) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for V35A-FTS)  P16B09F  Actuator Cut Circuit Stuck Off  


DESCRIPTION

The TCM monitors whether monitoring control is being performed properly for transmission control. If a malfunction is detected, it cuts the solenoid actuator. The solenoid actuator cut circuit immediately after the ignition switch is turned off, the TCM stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P16B09F Actuator Cut Circuit Stuck Off ECU malfunction (1 trip detection logic).
·

Solenoid (SL1) valve

·

Solenoid (SL2) valve

·

Solenoid (SL3) valve

·

Solenoid (SL4) valve

·

Solenoid (SL5) valve

·

Solenoid (SL6) valve

·

Solenoid (SLT) valve

·

Solenoid (SLU) valve

·

Solenoid (SC1) valve

·

Solenoid (SL) valve

·

Solenoid (SR) valve

·

TCM


Does not come on DTC stored SAE: P16B0

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off.

3.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

4.

Connect the cable to the negative (-) battery terminal.

5.

Turn the ignition switch to ON.

6.

Wait 1 second or more.

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

9.

Input the DTC: P16B09F.

10.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.




CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)>PRECAUTION

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTC (DTC P16B09F)
2.READ OUTPUT DTC (DTC P16B09F)
a.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Wait 1 second or more.


e.

Read the DTCs.

Powertrain > Transmission > Trouble Codes
50001 373
Result:
Result Proceed to
DTCs are not output A
DTC P16B09F is output B




A

B

3.REPLACE TCM
3.REPLACE TCM

NEXT

4.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5), (SL6), (SLT), (SLU), (SC1), (SL) AND (SR) VALVE
4.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5), (SL6), (SLT), (SLU), (SC1), (SL) AND (SR) VALVE

OK

NG

REPLACE SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5), (SL6), (SLT), (SLU), (SC1), (SL) OR (SR) VALVE