The TCM detects an erroneous downshift output to the automatic transmission or a gear shifting malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P170300 | AT Solenoid Output Malfunction | ECU malfunction (1 trip detection logic) |
·
Wire harness or connector
·
Transmission revolution sensor (SP2)
·
Transmission wire
·
Solenoid (SL1) valve
·
Solenoid (SL2) valve
·
Solenoid (SL3) valve
·
Solenoid (SL4) valve
·
Solenoid (SL5) valve
·
Solenoid (SL6) valve
·
Solenoid (SC1) valve
·
Solenoid (SL) valve
·
Solenoid (SR) valve
·
Solenoid (SLU) valve
·
TCM |
Comes on | DTC stored | SAE: P1703 |
When an erroneous downshift is output or a gear shifting malfunction is detected while downshifting or changing gears while driving, the TCM stores a DTC.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Perform the D Position Test inspection in Road Test.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P170300.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
| N/A |
·
Unable to perform DTC judgment
·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the automatic transmission are replaced
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C36)Location & Routingewd_type=routing;type=c;code=C36 |
||
| C36-6 (SL1+) - C36-25 (SL1-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C36-5 (SL2+) - C36-24 (SL2-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C36-7 (SL3+) - C36-26 (SL3-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C36-8 (SL4+) - C36-27 (SL4-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C36-3 (SL5+) - C36-22 (SL5-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C36-9 (SL6+) - C36-28 (SL6-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C36-4 (SLU+) - C36-23 (SLU-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C36-44 (SL) - Body ground | 20°C (68°F) | 11 to 15 Ω |
| C36-45 (SR) - Body ground | 20°C (68°F) | 11 to 15 Ω |
| C36-46 (SC1) - Body ground | 20°C (68°F) | 11 to 15 Ω |
| C36-6 (SL1+) or C36-25 (SL1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C36-5 (SL2+) or C36-24 (SL2-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C36-7 (SL3+) or C36-26 (SL3-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C36-8 (SL4+) or C36-27 (SL4-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C36-3 (SL5+) or C36-22 (SL5-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C36-9 (SL6+) or C36-28 (SL6-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C36-4 (SLU+) or C36-23 (SLU-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Speed (SP2) | Output shaft speed | Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) |
0 km/h (0 mph): Vehicle stopped (Output shaft speed is equal to vehicle speed) |
- |
| SP2 Sensor Voltage | SP2 sensor voltage | Min.: 0.000 V Max.: 4.999 V |
0.2 to 1.8 V: Idling | - |
| Tester Display |
|---|
| Speed (SP2) |
| SP2 Sensor Voltage |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Perform the D Position Test inspection in Road Test.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P170300 is output | B |
A
B
NEXT
Disconnect the transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C33)Location & Routingewd_type=routing;type=c;code=C33 |
||
| C33-30 (SP2O) - Body ground | Always | 99 to 101 Ω |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C33)Location & Routingewd_type=routing;type=c;code=C33 |
||
| C33-29 (SP2B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Transmission Revolution Sensor (SP2)) |
| *b | Component without harness connected (Transmission Wire) |
Disconnect the transmission revolution sensor (SP2) connector.
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR>REMOVAL
Disconnect the transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C33)Location & Routingewd_type=routing;type=c;code=C33 |
||
| Terminal 2 of the transmission revolution sensor (SP2) connector - C33-29 (SP2B) | Always | Below 1 Ω |
| Terminal 1 of the transmission revolution sensor (SP2) connector - C33-30 (SP2O) | Always | Below 1 Ω |
| Terminal 2 of the transmission revolution sensor (SP2) connector or C33-29 (SP2B) - Body ground | Always | 10 kΩ or higher |
| Terminal 1 of the transmission revolution sensor (SP2) connector or C33-30 (SP2O) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the transmission wire connector.
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C33,C36)Location & Routingewd_type=routing;type=c,c;code=C33,C36 |
||
| C33-29 (SP2B) - C36-12 (SP2B) | Always | Below 1 Ω |
| C33-30 (SP2O) - C36-31 (SP2O) | Always | Below 1 Ω |
| C33-29 (SP2B) or C36-12 (SP2B) - Body ground | Always | 10 kΩ or higher |
| C33-30 (SP2O) or C36-31 (SP2O) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
NEXT
Disconnect the transmission wire connector.
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C33,C36)Location & Routingewd_type=routing;type=c,c;code=C33,C36 |
||
| C33-23 (SL1+) - C36-6 (SL1+) | Always | Below 1 Ω |
| C33-24 (SL1-) - C36-25 (SL1-) | Always | Below 1 Ω |
| C33-19 (SL2+) - C36-5 (SL2+) | Always | Below 1 Ω |
| C33-20 (SL2-) - C36-24 (SL2-) | Always | Below 1 Ω |
| C33-13 (SL3+) - C36-7 (SL3+) | Always | Below 1 Ω |
| C33-14 (SL3-) - C36-26 (SL3-) | Always | Below 1 Ω |
| C33-15 (SL4+) - C36-8 (SL4+) | Always | Below 1 Ω |
| C33-16 (SL4-) - C36-27 (SL4-) | Always | Below 1 Ω |
| C33-11 (SL5+) - C36-3 (SL5+) | Always | Below 1 Ω |
| C33-12 (SL5-) - C36-22 (SL5-) | Always | Below 1 Ω |
| C33-25 (SL6+) - C36-9 (SL6+) | Always | Below 1 Ω |
| C33-26 (SL6-) - C36-28 (SL6-) | Always | Below 1 Ω |
| C33-17 (SLU+) - C36-4 (SLU+) | Always | Below 1 Ω |
| C33-18 (SLU-) - C36-23 (SLU-) | Always | Below 1 Ω |
| C33-5 (SL) - C36-44 (SL) | Always | Below 1 Ω |
| C33-6 (SR) - C36-45 (SL) | Always | Below 1 Ω |
| C33-7 (SC1) - C36-46 (SC1) | Always | Below 1 Ω |
| C33-23 (SL1+) or C36-6 (SL1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-24 (SL1-) or C36-25 (SL1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-19 (SL2+) or C36-5 (SL2+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-20 (SL2-) or C36-24 (SL2-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-13 (SL3+) or C36-7 (SL3+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-14 (SL3-) or C36-26 (SL3-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-15 (SL4+) or C36-8 (SL4+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-16 (SL4-) or C36-27 (SL4-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-11 (SL5+) or C36-3 (SL5+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-12 (SL5-) or C36-22 (SL5-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-25 (SL6+) or C36-9 (SL6+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-26 (SL6-) or C36-28 (SL6-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-17 (SLU+) or C36-4 (SLU+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-18 (SLU-) or C36-23 (SLU-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-5 (SL) or C36-44 (SL) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-6 (SR) or C36-45 (SR) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-7 (SC1) or C36-46 (SC1) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG