Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0472752 AUTOMATIC TRANSMISSION SYSTEM J

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

The transmission control switch detects when the shift lever is moved to M.

Using the transmission control switch, when the shift lever is in M, it is possible to select between 1st and 10th gears (M1 to M10).

Moving the shift lever to "+" once selects the next higher gear, and moving the shift lever to "-" once selects the next lower gear.

WIRING DIAGRAM

C458223E01
5.979,5.25 6.385,5.583 0.406,0.333 10 false ECM 5.99,5.073 6.448,5.271 0.458,0.198 10 false B1 2.25,3.417 4.375,3.885 2.125,0.469 10 false Transmission Control Switch (Shift Lock Control Unit Assembly) 2.26,3.26 2.719,3.458 0.458,0.198 10 false I74*2 3.177,4.885 4.844,5.292 1.667,0.406 10 false TCM 0.417,5.448 2.49,5.719 2.073,0.271 10 false : CAN Communication Line 5.604,1.979 6.219,2.177 0.615,0.198 10 false SFTU 5.615,1.396 6.229,1.594 0.615,0.198 10 false SFTD 5.615,2.573 6.229,2.771 0.615,0.198 10 false S 3.875,2.573 4.49,2.771 0.615,0.198 10 false S 3.646,1.979 4.26,2.177 0.615,0.198 10 false SFTU 3.635,1.396 4.25,1.594 0.615,0.198 10 false SFTD 2.75,1.396 3.365,1.594 0.615,0.198 10 false E 2.75,2.563 3.365,2.76 0.615,0.198 10 false IG 0.385,2.698 2.99,2.896 2.604,0.198 10 false from ECU-IGR NO. 2 Fuse 5.333,2.563 5.948,2.76 0.615,0.198 10 false 32 5.333,1.979 5.948,2.177 0.615,0.198 10 false 12 5.333,1.396 5.948,1.594 0.615,0.198 10 false 11 4.094,1.396 4.708,1.594 0.615,0.198 10 false 3*2 4.094,1.979 4.708,2.177 0.615,0.198 10 false 1*2 4.094,2.563 4.708,2.76 0.615,0.198 10 false 5 2.542,2.573 3.156,2.771 0.615,0.198 10 false 4 2.542,1.396 3.156,1.594 0.615,0.198 10 false 2 6.5,1.24 7.042,1.438 0.542,0.198 10 false 12 V 6.5,1.833 7.042,2.031 0.542,0.198 10 false 12 V 4.094,1.219 4.708,1.417 0.615,0.198 10 false 1*1 4.094,1.792 4.708,1.99 0.615,0.198 10 false 3*1 2.26,3.094 2.719,3.292 0.458,0.198 10 false I73*1 0.302,4.719 1.99,4.917 1.688,0.198 10 false *1: for LHD 0.302,5.052 1.99,5.25 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS (Shift SW Status (S Range))
a.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (S Range) Sport mode select switch status ON or OFF
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Powertrain > Engine > Data List
Tester Display
Shift SW Status (S Range)
50003 372 27

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

2.READ VALUE USING GTS (SPORT SHIFT UP SW AND SPORT SHIFT DOWN SW)

B

6.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
2.READ VALUE USING GTS (SPORT SHIFT UP SW AND SPORT SHIFT DOWN SW)
a.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sport Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sport Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-
Powertrain > Engine > Data List
Tester Display
Sport Shift Up SW
Sport Shift Down SW
50003 372 26,25

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

B

3.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
3.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.
C458671C03
0.219,0.99 0.615,1.313 0.396,0.323 1.292,1.729 1.646,1.313 true 2.698,1.729 2.313,1.302 true 1.979,1.729 1.958,1.333 true 0.375,0.313 0.688,0.51 0.313,0.198 10 false *a 1.948,1.781 2.104,1.979 0.156,0.198 10 false E 2.542,1.771 3.156,1.969 0.615,0.198 10 false SFTD 1.073,1.76 1.688,1.958 0.615,0.198 10 false SFTU 0.323,1.063 0.781,1.26 0.458,0.198 10 false I73 0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for LHD
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


for LHD:

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I73)Location & Routing

Click Connector(I73)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transmission Control Switch (Shift Control Unit Assembly)

I73-3 (SFTU) - I73-2 (E) Shift lever held in "+" Below 1 Ω
I73-3 (SFTU) - I73-2 (E) Shift lever not held in "+" 10 kΩ or higher
I73-1 (SFTD) - I73-2 (E) Shift lever held in "-" Below 1 Ω
I73-1 (SFTD) - I73-2 (E) Shift lever not held in "-" 10 kΩ or higher



c.
C458671C04
0.219,0.99 0.615,1.313 0.396,0.323 1.292,1.729 1.646,1.313 true 2.698,1.729 2.313,1.302 true 1.979,1.729 1.958,1.333 true 0.375,0.302 0.688,0.5 0.313,0.198 10 false *a 1.948,1.781 2.104,1.979 0.156,0.198 10 false E 2.542,1.771 3.156,1.969 0.615,0.198 10 false SFTU 1.073,1.76 1.688,1.958 0.615,0.198 10 false SFTD 0.323,1.063 0.781,1.26 0.458,0.198 10 false I74 0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for RHD
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


for RHD:

Disconnect the transmission control switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I74)Location & Routing

Click Connector(I74)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transmission Control Switch (Shift Control Unit Assembly)

I74-1 (SFTU) - I74-2 (E) Shift lever held in "+" Below 1 Ω
I74-1 (SFTU) - I74-2 (E) Shift lever not held in "+" 10 kΩ or higher
I74-3 (SFTD) - I74-2 (E) Shift lever held in "-" Below 1 Ω
I74-3 (SFTD) - I74-2 (E) Shift lever not held in "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.

Disconnect the transmission control switch connector.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B1-12 (SFTU) - Body ground Shift lever held in "+" Below 1 Ω
B1-12 (SFTU) - Body ground Shift lever not held in "+" 10 kΩ or higher
B1-11 (SFTD) - Body ground Shift lever held in "-" Below 1 Ω
B1-11 (SFTD) - Body ground Shift lever not held in "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.
C458671C05
0.156,0.99 0.656,1.292 0.5,0.302 0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.302,0.271 0.615,0.469 0.313,0.198 10 false *a 1.906,1.802 2.375,2 0.469,0.198 10 false IG 0.646,1.771 1.021,1.979 0.375,0.208 10 false S 0.313,1.063 0.771,1.26 0.458,0.198 10 false I73 0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for LHD
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


for LHD:

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I73)Location & Routing

Click Connector(I73)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transmission Control Switch (Shift Control Unit Assembly)

I73-4 (IG) - I73-5 (S) Shift lever in M, "+" or "-" Below 1 Ω
I73-4 (IG) - I73-5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher



c.
C458671C06
0.156,0.99 0.656,1.292 0.5,0.302 0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.302,0.271 0.615,0.469 0.313,0.198 10 false *a 1.906,1.802 2.375,2 0.469,0.198 10 false IG 0.646,1.771 1.021,1.979 0.375,0.208 10 false S 0.313,1.063 0.771,1.26 0.458,0.198 10 false I74 0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for RHD
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


for RHD:

Disconnect the transmission control switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I74)Location & Routing

Click Connector(I74)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transmission Control Switch (Shift Control Unit Assembly)

I74-4 (IG) - I74-5 (S) Shift lever in M, "+" or "-" Below 1 Ω
I74-4 (IG) - I74-5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

NG

REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I73)Location & Routing

Click Connector(I73)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transmission Control Switch (Shift Control Unit Assembly)

I73-4 (IG) - Body ground Ignition switch ON 11 to 14 V
I73-4 (IG) - Body ground Ignition switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I74)Location & Routing

Click Connector(I74)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transmission Control Switch (Shift Control Unit Assembly)

I74-4 (IG) - Body ground Ignition switch ON 11 to 14 V
I74-4 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - TCM)
a.

Disconnect the transmission control switch connector.


b.

Disconnect the TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(I73,B1)Location & Routing

Click Connector(I73)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transmission Control Switch (Shift Control Unit Assembly)

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

I73-5 (S) - B1-32 (S) Always Below 1 Ω
I73-5 (S) - Body ground Always 10 kΩ or higher
B1-32 (S) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(I74,B1)Location & Routing

Click Connector(I74)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transmission Control Switch (Shift Control Unit Assembly)

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

I74-5 (S) - B1-32 (S) Always Below 1 Ω
I74-5 (S) - Body ground Always 10 kΩ or higher
B1-32 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR