Home › Suspension › SUSPENSION CONTROL › ELECTRONIC-KINETIC DYNAMIC SUSPENSION SYSTEM
RM38G0E _53 Suspension _100546 SUSPENSION CONTROL _0470891 ELECTRONIC-KINETIC DYNAMIC SUSPENSION SYSTEM C

SUSPENSION CONTROL  ELECTRONIC-KINETIC DYNAMIC SUSPENSION SYSTEM  C183314  Fr Stabilizer Solenoid A Control Circuit Circuit Short to Ground or Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C183314 Fr Stabilizer Solenoid A Control Circuit Circuit Short to Ground or Open Open circuit detected in solenoid valve
·

Front stabilizer housing sub-assembly

·

Harness or connector

·

Stabilizer control ECU


Electronic-Kinetic Dynamic Suspension System (E-KDSS)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - FRONT SPEED SENSOR RH)
a.

Disconnect the Q14 stabilizer control ECU connector.


b.

Disconnect the B13 front speed sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q14,B13)Location & Routing

Click Connector(Q14)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Stabilizer Control ECU

Click Connector(B13)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Front Speed Sensor Wire RH

Q14-2 (FNC+) - B13-2 (SBFD) Always Below 1 Ω
Q14-3 (FNC-) - B13-8 (CRFD) Always Below 1 Ω
Q14-2 (FNC+) or B13-2 (SBFD) - Body ground Always 10 kΩ or higher
Q14-3 (FNC-) or B13-8 (CRFD) - Body ground Always 10 kΩ or higher



d.

Connect the B13 front speed sensor RH connector.


e.

Connect the Q14 stabilizer control ECU connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT FRONT SPEED SENSOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT FRONT SPEED SENSOR RH
C456836C03
0.958,0.781 1.333,1.063 0.375,0.281 3.604,0.75 4.031,1.021 0.427,0.271 6.01,1.281 6.01,1.135 6.01,1.135 5.427,0.969 true 6.083,0.292 5.896,0.292 5.896,0.292 5.427,0.74 true 1.938,0.99 1.417,1.25 1.417,1.25 1.417,1.333 true 1.99,0.75 1.667,0.333 1.667,0.333 1.5,0.333 true 0.292,0.115 0.604,0.271 0.313,0.156 10 false *a 1.042,0.833 1.479,1 0.438,0.167 10 false z13 6.146,0.219 6.594,0.427 0.448,0.208 10 false SBFD 1.083,0.271 1.531,0.479 0.448,0.208 10 false CRFD 3.688,0.802 4.135,1.01 0.448,0.208 10 false B13 1.99,0.115 2.281,0.344 0.292,0.229 10 false *A 5.042,0.083 5.333,0.313 0.292,0.229 10 false *B 1.26,1.385 1.708,1.594 0.448,0.208 10 false SBFD 5.833,1.333 6.281,1.542 0.448,0.208 10 false CRFD
*A Front Stabilizer Housing Sub-assembly Side *B Wire Harness Side
*a Component without harness connected
(Front Speed Sensor RH)
- -


a.

Disconnect the B13 front speed sensor RH connector.


b.

Disconnect the z13 front stabilizer housing sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B13,z13)Location & Routing

Click Connector(B13)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Front Speed Sensor Wire RH

Click Connector(z13)Engine Compartment>other>Front Stabilizer Control Wire , Front Speed Sensor Wire RH

B13-2 (SBFD) - z13-4 (SBFD) Always Below 1 Ω
B13-8 (CRFD) - z13-2 (CRFD) Always Below 1 Ω
B13-2 (SBFD) or z13-4 (SBFD) - Body ground Always 10 kΩ or higher
B13-8 (CRFD) or z13-2 (CRFD) - Body ground Always 10 kΩ or higher



d.

Connect the z13 front stabilizer housing sub-assembly connector.


e.

Connect the B13 front speed sensor RH connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT STABILIZER HOUSING SUB-ASSEMBLY (FRONT NORMAL CLOSE SOLENOID VALVE)

NG

3.INSPECT FRONT STABILIZER HOUSING SUB-ASSEMBLY (FRONT NORMAL CLOSE SOLENOID VALVE)
a.
C457010C02
0.104,0.083 0.417,0.24 0.313,0.156 10 false *a
*a Component without harness connected
(Front Stabilizer Housing Sub-assembly)


Disconnect the z13 front stabilizer housing sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 4 25°C (77°F) 4.58 to 5.02 Ω



c.

Connect the z13 front stabilizer housing sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE STABILIZER CONTROL ECU

NG

REPLACE FRONT STABILIZER HOUSING SUB-ASSEMBLY