| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C183614 | Fr Stabilizer Solenoid B Control Circuit Circuit Short to Ground or Open | Open circuit detected in solenoid valve |
·
Front stabilizer housing sub-assembly
·
Harness or connector
·
Stabilizer control ECU |
Electronic-Kinetic Dynamic Suspension System (E-KDSS) |
Refer to C183612.
Click hereSuspension>SUSPENSION CONTROL>ELECTRONIC-KINETIC DYNAMIC SUSPENSION SYSTEM>C183612
Disconnect the Q14 stabilizer control ECU connector.
Disconnect the B13 front speed sensor RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Q14,B13)Location & Routingewd_type=routing;type=c,c;code=Q14,B13 |
||
| Q14-5 (FNO+) - B13-1 (SBFU) | Always | Below 1 Ω |
| Q14-6 (FNO-) - B13-7 (CRFU) | Always | Below 1 Ω |
| Q14-5 (FNO+) or B13-1 (SBFU) - Body ground | Always | 10 kΩ or higher |
| Q14-6 (FNO-) or B13-7 (CRFU) - Body ground | Always | 10 kΩ or higher |
Connect the B13 front speed sensor RH connector.
Connect the Q14 stabilizer control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | Front Stabilizer Housing Sub-assembly Side | *B | Wire Harness Side |
| *a | Component without harness connected (Front Speed Sensor RH) |
- | - |
Disconnect the B13 front speed sensor RH connector.
Disconnect the z13 front stabilizer housing sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B13,z13)Location & Routingewd_type=routing;type=c,c;code=B13,z13 Click Connector(z13)Engine Compartment>other>Front Stabilizer Control Wire , Front Speed Sensor Wire RHewd_type=component;type=c;code=z13;pinno=3,1 |
||
| B13-1 (SBFU) - z13-3 (SBFU) | Always | Below 1 Ω |
| B13-7 (CRFU) - z13-1 (CRFU) | Always | Below 1 Ω |
| B13-1 (SBFU) or z13-3 (SBFU) - Body ground | Always | 10 kΩ or higher |
| B13-7 (CRFU) or z13-1 (CRFU) - Body ground | Always | 10 kΩ or higher |
Connect the z13 front stabilizer housing sub-assembly connector.
Connect the B13 front speed sensor RH connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected (Front Stabilizer Housing Sub-assembly) |
Disconnect the z13 front stabilizer housing sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 3 | 25°C (77°F) | 23.5 to 25.7 Ω |
Connect the z13 front stabilizer housing sub-assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG